Shopping Cart

Your cart is empty.

Your cart is empty.

ELING 85mm GPS Speed Gauge Meter 35 MPH Speedometer Replacement with Backlight IP67 Waterproof 12 24 Volts (Black+Nickel Stainless Steel)

Free shipping on orders over $29.99

$67.99

$ 30 .99 $30.99

In Stock

1.:0-35mph


2.Color:Black+black


About this item

  • Cut an 85mm (3 3/8") hole in the panel and allow a clearance of 55mm (2 3/16”) behind the panel to fit the gauge. Put the gauge in the hole and screw down.
  • 12/24V Working Voltage, Red and Yellow backlights available,
  • Securely fasten the GPS antenna, preferably outdoors (or inside front windscreen) so that it has a clear view of the sky to pick up satellite signal. Connect the antenna cable to socket in the back of the gauge. Do not cut cable.
  • OverSpeed Buzzer Alarm
  • The gauge has the advantages of high precision, quick location confirmation and short start up time



Product Description

TNG35M-BN-Banner

Product Features:

-Suitable for all vehicles and off-road vehicles

-The signal comes directly from the satellite signal receiver(GPS Antenna), don't need other speed sensor

-The gauge has the advantages of high precision, quick location confirmation and short start up time

-IP67 waterproof and dustproof grade

-Reverse polarity protection and anti-fogging performance

-No Stationery Drift

-Stepper motors used for full range of stepping gauges, great feature with its less power consumption, longer life, higher precision, etc.

Product Introduction

TNG35M-BN-侧面

How to install it?

- Cut an 85mm (3 3/8") hole in the panel and allow a clearance of 55mm (2 3/16”) behind the panel to fit the gauge.

- Put the gauge in the hole and screw down.

- For the GPS antenna, you should securely fasten it in the flat position, black side upwards, preferably outside (or inside front windscreen) so that it has a clear view of the sky to pick up satellite signal. Connect the antenna cable to socket in the back of the gauge. And do not cut cable.

TNG35M-BN-右斜

GPS speedometer keeps counting?

After installation in the first time, GPS speedometer needs to search for signal, that's the reason that LCD counts numbers all the time.

After getting signal, LCD will come back to 0. It is normal.

TNG35M-BN-左斜

External button wiring?

For the external button, one pin is connected to white wire of speedometer, the other to power negative/ground.

Technical Data

Fixing dimension 85mm(3-3/8")
Speed indicating range 0-35MPH 0-55km/h
Working Voltage 12V/24V
LCD indicates Course over ground
Backlight Red and Yellow available
Working temperatures - 40 to 85°C
Operation mode LCD display, stepper motor
OverSpeed Alarm OverSpeed Buzzer Alarm (Value Adjustable)
TNG35M-BN-正视

How to change "BUZZ"?

1. Press the button for 2-3 seconds first and then turn on the power supply.

2. Release the button after seeing “BUZZ”; Press the button to set up the target overspeed buzzer alarm threshold value.

3. After adjustment, release button first, then wait for menu to complete flashing.

4. Turn off the power supply, then turn on again. Odometer will record the setting.

TNG35M-BN-合集

Package Includes:

1x GPS speedometer

1x GPS Antenna

1x Multi-plug socket

1x External Button

1x Installation Instruction


roger young
Reviewed in the United States on October 16, 2024
It works
EvD
Reviewed in the United States on April 22, 2024
I love the look of the speedo so I ordered it for my 24v bus.After wiring everything in the speedo won’t do anything.Oddly enough the backlight won’t even come on which made me think that I had made a mistake but I tested everything with my test light and even continuity though the ground wire and have power and ground to the unit but it’s not doing anything.
frodo_bagginsjdg
Reviewed in the United States on September 11, 2023
The media could not be loaded.
troy
Reviewed in the United States on July 9, 2023
The wire diagram only shows this model using pen 1-5. I was very curious what in 6,7 and 8 did so I energize them for 12 V, and to my surprise they were extra colors. 6 is the left side and green, 7 is the right side green and 8 is the top side in blue.With all 3 extra pins energized (678) the color goes from a green-blue-green. Very cool hidden feature and all you have to do is re-pin the back.
ibtd
Reviewed in the United States on July 27, 2023
Just got this a couple days ago to replace worthless non functional paddle wheel speedometers in my skiboat. Super easy install! Skied this morning after checking against other GPS devices. This thing is spot on and way cheaper that trying to fix the inaccurate factory ones. Ordered a second one for astheics and in case one should ever lose signal (which never happened).UPDATE: Got the 2nd one today. Easy swap in under an hour.
PAUL
Reviewed in the United States on November 19, 2023
This fitted the need for a RIB boat without GPS. It also more or less matches my factory Honda RPM gauge so looks good. Nice looking Speedo.
CHRISTOPHER A BLOOR
Reviewed in the United States on November 19, 2022
used this all boating season. Much more precise for water sports than the factory water pressure driven gauge. It does drop out occasionally if it looses a signal, but not for too long.