Your cart is empty.
Your cart is empty.Cnc extender adapter made especially for 1/8" Shank router bits., #47648, (D) diameter 7/16, (D) diameter 7/16, overall length (L) 2-1/4, Max RPM 18, 000, L1 19/32, L2 13/16, L3 1/4, D1 1/8, 47648 1/4 inch shank CNC extension adapter for 1/8 inch shank router bits
P. Larose
Reviewed in Canada on November 1, 2024
Use this in my 1/4 inch DeWalt router to convert it to a rotary type tool (like Dremel).No more burnt out Dremel motor.
MT
Reviewed in the United States on April 8, 2024
I don’t recommend this for high accuracy, low T.I.R CNC use, but great for general purpose use.
msaxy
Reviewed in the United States on January 18, 2023
This will allow me to use some of my dremel bits with my hand grinder. Looks to be well machined, and the 1/8" collet allows a pair of wrenches to be used with tightening down 1/8" diameter shafted bits. I had initially ordered Amana's RB102, which is a slotted 1/4" to 1/8" adapter sleeve, but this was simply way too stiff to allow me to use this in my grinder. I was afraid that I would ruin me collet with the amount of pressure that is needed for the sleeve to compress and to hold everything tight.
Michael Grey
Reviewed in the United States on August 23, 2022
This may work for hand held router work but don't even try this in a CNC. The runout is entirely unacceptable. Go to elairecorp.com if you want a 1/8" adapter for your CNC trim router. Cost less than this and I have now spent $42 for something I can't use and now can't return.
D. Miller
Reviewed in Canada on July 16, 2022
I need this so my Milwaukee die grinder could be used with 1/8" shank grinding bits. This did the job and worked as an extension as well. Was apprehensive about the cost but it is made very well and worth the cost.
Patrick
Reviewed in Canada on February 25, 2022
Seems good but I'm scared of tightening it too tight and breaking it. Looking back I shoulda just found a smaller collet instead.
Adrian Ruiz
Reviewed in the United States on July 25, 2021
It is as it's described
Abbey
Reviewed in the United States on June 9, 2021
This is a mainstay tool that I use constantly in my CNC. It holds the small tool rigidly and is easy to change tools.
Jsonsalla
Reviewed in the United States on September 12, 2020
I use this to adapt the 1/4" collet on my CNC router to 1/8" for small router bits. Grips the 1/8" bits tightly, no slippage. Very good balance, no vibration and clean cuts. Quality product at a very reasonable price.
Jason E.
Reviewed in the United States on December 5, 2020
Only got about 30 hours out of this part before it broke. Broke when I went to change bits twisted threads right off. And it’s not like I put very much torque on this bolt it’s only 11 mm so you know you don’t have to tighten it very hard it’s just very cheap design don’t waste your money
Rich in SLO
Reviewed in the United States on January 22, 2020
Gives me a little added room on my CNC so I can clear clamps with the router.Seems to have little to no runout. (I think my dial indicator read around 0.005") I'm only cutting wood so it's not a problem. Also, using the cheap 10packs of 1/8" two flute bits which may contribute to runout. (Haven't broken one, yet.)
Benjamin guerrero
Reviewed in Mexico on December 28, 2019
Es un artículo muy práctico que no encuentro en cualquier establecimiento, lo usare para mí cnc
Recommended Products
$59.33
$ 31 .99 $31.99
$22.08
$ 10 .99 $10.99