Your cart is empty.
Your cart is empty. This PoE adapter only fit for 10/100Mbps networks.
Applications:
IP Phone
Wireless Access point devices
IP Security Camera Systems
Features:
1. Used for 10/100Mbps networking
2. Save you money by using an existing Ethernet line to deliver data and power.
3. Easily connect any POE supported device to a NON-PoE LAN switch port.
4. Used to connect a wireless access point, IP phone, network camera, or any POE powered device to a LAN switch.
5. Reduce Wiring Costs by powering devices through your existing Ethernet line rather than running new AC power lines.
6. You need to do is connect this iCreatin PoE Injector to the LAN switch port, and then use your existing Ethernet Cable to deliver DC power and data to your device.
7. Protect Your Equipment Now that you are running DC power to your networked equipment through the Cat5 cabling, you need to be sure that your devices are protected from power problems.
8. short circuit , Over Current and Over Voltage Protection, keeping your devices safe. It is also protect your products from overloads over 350mA and high voltages exceeding 52Vdc.
Specifications
2 RJ45 Shielded Ethernet ports
Input: 100-240VAC 50/60Hz
Output: 48V 0.35A
Power feed Pins: V+ 4,5; V- 7,8;
Data rate: 10\100Mbps
Deliver power up to about 325 feet
What in Box?
1 x wall PoE injector 48V 15.4W
Chip Bell
Reviewed in the United States on January 7, 2024
Got a older really expensive ptz dome camera and after finally figuring out this was how to power it I looked at alternatives. This was the most affordable way that I could find. I wasn't even sure it worked and so wasn't going to invest much money. Anyway, it worked perfectly and the real test is that I plugged it in and forgot about it. No problems.
Gray Dog
Reviewed in the United States on August 31, 2023
Drives my POE camera just fine.
John B. Slade
Reviewed in the United States on March 4, 2023
I measured the current of that adapter 48VDC 1/2 A. It is limited (200mA) of 500mA for 48.3V staying. If more than 200mA current, it'll be 45v to 46v drop. Not recommended.
Jac
Reviewed in the United States on October 25, 2023
I've purchased this product many times before so we know it's a good quality Passive injector. We'll continue to use them. I would recommend if you want this type Product.
N6AC
Reviewed in the United States on June 14, 2022
The unit appears to work as expected.We tried it out on a Reolink RLC-842A and everything works normally.BUT, anyone who connects as shown in unedited figure will probably blow up their router or LAN switch etc., because the port labelled "Data & Power Out" carries 48 volts DC on pins 4 &5 relative to the return on pins 7 & 8. Be sure the LAN cable goes to the correct port !!!
Autonomy1983
Reviewed in the United States on February 14, 2022
Used it to extend POE for a camera and it's working just fine.
Mark Twain
Reviewed in the United States on December 17, 2022
Yeah so where to begin. Depending upon which diagram you follow it’s 50/50 whether you will blow up your router or switch, because they show it both right and wrong. Follow one diagram and you pump power in the wrong direction. How much power, you might wonder? Well that’s very unclear as well bThey say it is 48 volts and 15.4 watts in this ad here.On the thing itself it says only 48 watts, and. I other info. No way this is 48 watts.In the Q&A here the seller claims it’ll put out 12volts, 24 volts, or 48volts and will auto-sense which is needed. this is TOTAL NONSENSE! It cannot do any such thing.Who knows what it really puts out, probably 48V but I cannot trust my expensive gizmos to anyone who gets this much crap wrong. The device itself has errors on it, as does the ad, the specs, everything that could be wrong is wrong somewhere. I want a refund.
WannaDoo83
Reviewed in the United States on April 6, 2020
This PoE injector works perfectly for our Ubiquiti WiFi access point in our office.. Plugged it in, and it instantly worked beautifully! No issues at all. Happy.
Recommended Products
$47.99
$ 24 .99 $24.99