Your cart is empty.
Your cart is empty.Product Description
HIGH INTENSITY LED CHIP
Super bright with Fast on/off Response Time for Driving Safety.
PLUG & PLAY
Direct Plug & Play, Installs in 15 minutes or less.
EXTERNAL LOAD RESISTORS
Includes external load resistors to solve any hyper-flashing issues.
Jeremiah James Canady
Reviewed in the United States on September 25, 2024
only thing i disliked about these lights were you have to cut and splice the resistors into the wires, its not a plug and play like i thought but they are bright and we will see how long they last
Darrell
Reviewed in the United States on July 28, 2024
Replaced my OEM lights with these. Went right in, no problem. Mostly Plug-n-play. I did however end up using the provided resistors for hyper-flash. I didn't have it at first, and was happy, But after they were on a few minutes it started to hyper flash. :-( Adding in the resistors did fix it. Mounted them on the metal frame. THEY DO GET HOT! Instructions on the box are WRONG (as others have said, Thank you for that). One resistor wire goes to red, the other to black. I spliced them on the light assembly side, not the Jeep side.PROS:1. Looks nice (I got the smoked lens)2. Metal housing.3. Wires and connector look good.4. Resistors encased in heat sync with mounting holes (if you need them)5. Went in pretty easyCONS:1. Ended up getting hyper-flash, had to use the resistors2. Not very much difference between the brightness of flashing vs continuously on. Kind of hard to tell the difference. My headlights have the flashing ring so I'm ok with it. Would have returned if I didn't.Hopefully they last a while. If they die, I will try a different light assembly.
Kent Valente
Reviewed in the United States on January 10, 2024
So I definitely went with the Amber which is right on point to me to black out the lights. You're not going to get the clarity that you're needing. There's something about these. The the rich amber glow when the lights are on. They're amazing. You can be seen the turn. Turn signal goes well. Hands down one of the easiest mods I've done. I had plenty of room. I didn't have to take the grill off. I could just reach right in pop out. Feel like pop the new one in boom. Boom boom took me every bit of 5 minutes worth every penny. I have a 2016 Jeep Wrangler Rubicon and no problems whatsoever with light flicker anything like that. I highly recommend this product. You will be completely satisfied.
Customer
Reviewed in Canada on September 26, 2022
Very easy installation. Are they brighter? not really.. I'd say about the same... they do have a sharper, chrispness to the colour. I'd say they are more saturated.. so better visibility for sure.
Geoff Fletcher
Reviewed in Canada on June 7, 2021
Very easy and straight forward install. Look great on my JK. Glad I chose the amber look, as they look great even when off. Resistors were not required. I do have LED headlights from the factory, not sure if that’s why.I set them as my DRLs and they work and look great. Super bright.Only 1 small issue and I’m not sure if it’s because of the lights themselves or the Jeep. During drl operation they drop out when the turns signal is activated. That is normal. But when I have the full lighting on and the turn signal is activated, the bulb is almost too bright and it’s harder to see the flashing turn signal. It’s not a hyper flash. I just wish they’d drop out entirely for the flash, not just partially.Aside from that I’m very happy. Great value for these lights.
Medic1967
Reviewed in Canada on March 18, 2021
So I had bought and returned a different manufacturer's product. THESE are the way! Solid-feeling, bright and look GREAT. Install tip - the mounting tabs are not part of the housing - you have to attach them as part of a bracket to the light assembly. Don't put them on the light first. Attach the bracket part to your grille FIRST- then use the set screw to attach the lamp in place. If you do it this way it will be MUCH EASIER. Also - didn't require the provided resistors for flicker prevention. The lights work just fine without on my Jeep.
Jonny
Reviewed in Canada on February 25, 2021
Fit and finish was perfect and crazy bright. Quality reinforced plastic housing. Not the shiny black brittle plastic. Connectors fit perfectly and ZERO hyper flashing WITHOUT using the load resistors.
Tim
Reviewed in Canada on February 14, 2021
Install was easy but pictures in manual are not clear . I did not need fast blink resistors, make sure you check all wires prior to plugging in one wire was lose that caused fast flash. Once I pushed it in and plugged in again no fast flash. Overall good signal lights , bright.
Don Gaudette
Reviewed in the United States on January 18, 2021
These turn signals are awesome. I originally got their cheaper set for $35 and was really disappointed with the brightness so I figured I’d just cough up the extra $15 and get these and I was not disappointed. These are super bright. And they look pretty cool if you ask me. The cheaper set I got wasn’t even as bright as the stock lights, but these are like 20-30x brighter than the stock ones. I can see them edge to edge in my two car garage, they show on the floor, they show all the way to the ceiling. They’re bright. I got the clear lens for max brightness. I have a 2016 JKU Sport and I didn’t have to use the resistors. No hyperflash, no issues at all so far. Plug and play. The install into the grille was a bit more difficult than some people with limited mechanical ability would like but it wasn’t too hard to figure out. Easiest way is to take the grille completely off and set it face down on a table or workbench, take the old lights out, figure out which way you need the bracket for each side, then put the brackets in the grille slots, then lift the lights into place, you can watch the tabs sliding into the slots in the back of the light. Once the tabs are in the slots all the way put the screw in and tighten it down. Got one in no problem, the other one fought me a little bit because the backing bracket isn’t a perfect fit in the slots so I switched them and then they both went right in. Just be gentle and keep trying till you get it, it’s really not that hard. That bracket is going to hold those lights in a lot better than a couple of little plastic tabs like the stock ones. If you’re not confident then I’m sure a shop will install them for you. Overall I’m extremely happy with these. 5/5 would recommend and would buy again. Will update down the road on how they hold up.
Josh
Reviewed in the United States on April 13, 2021
Just got done installing these in my 2015 Wrangler JKU. They look and feel high quality. Before I installed them, I hooked them up to the wires to check function. They worked as expected with no hyperflash and they're nice and bright.Install was a breeze. The bracket and light tabs line up just so, but once you figure it out, they snap right into place and fit snugly, but not so snug that they're hard to push together. The combination alignment tabs and screw for the secure fit is pretty clever and works as designed. Note, that reviewers who said their lights popped out while driving installed them wrong! Admittedly, the instructions could be better, but the grill tab goes between the light and the tabbed bracket. There's a picture in the instructions that show this. Install it right, it'll stay just fine.The lights are pretty sleek looking. They're not quite flush with the grill like the OEM ones are, but they don't look any worse for it.Finally, props to Xprite for all the hardware it came with. Not just the resistors (which thankfully I didn't need) and mounting hardware, but also extra metal tabs for the grill (the ones that attach it to the rest of the Jeep at the bottom) and wire clamps for the resistor wires so if you do need the resistors, this seems to come with everything needed to wire them up.Overall, super pleased so far!
Joe B
Reviewed in the United States on October 18, 2020
They Amber Parking/Turn Signal lights actually look pretty clean and put out plenty of light from the three LED bulbs inside. I actually did a full Xprite Light upgrade (Halo Headlights, Halo Fog lights, Tail lights, and these parking/turn signal lights.I went with Amber to keep a clean, factory type look and it definitely looks better than clear with Amber LED lights (compared to another Jeep with the clear ones).Install was a breeze. The supplied plugs worked flawlessly and I did not need to install an anti-flicker relay; nor, were there any canbus errors.I will be reviewing all the lights and will have video uploads for them, so stay tuned Amazon. For the money, these can’t be beat. I cannot speak to longevity and I have not seen any moisture build up inside, mine.
Recommended Products