Shopping Cart

Your cart is empty.

Your cart is empty.

XINGYHENG 2Pcs DC 3-5V MAX6675 Themocouple Module Board and 2PCS K Type Themocouple Temperature Sensor with Cable Cord

4.4 (10) Write Review
Free shipping on orders over $29.99

$10.59

$ 4 .99 $4.99

In Stock
  • Super Material: Made of high quality use electronic components, high structural strength, impact resistance, strong shock resistance. On-chip cold junction compensation. High-impedance differential inputs. Thermocouple break detection, excellent electrical conductivity, safe and reliable, long mechanical life.
  • Package Include: Include 2pcs MAX6675 Module, 2pcs K Type Themocouple temperature sensor, and cable thread.
  • Operating Voltage Range and Temperature Range: Operating voltage Range: 3.0~5.5V. Operating Current: 50mA. Operating Temperature Range: ̈20Degrees Celsius - 85Degrees Celsius
  • High quality: Super wear-resistant, anti-oxidation and corrosion resistance, reliable operation and low power consumption. No electromagnetic interference, strong anti-interference, strong compatibility.
  • A Wide Range Of Application: Widely used in especially for single-chip computer enthusiasts, students, scientific research units experiment, prototype development, room temperature measurement, car modification, car air conditioners, refrigerators, freezers, and low temperature drying box and other proposed, silos, storage tank, telecommunications room, power room, such as cable trough temperature bearing, cylinder, textile machinery, air conditioning, and so on


About us:
The MAX667 module features a 12-bit resolution serial thermocouple analog-to-digital converter with cold junction compensation, linearity correction, and thermocouple break detection.
The main features of the MAX6675 are as follows
1. Simple SPI serial port temperature value output.
2. The temperature range from 0 °C to 1024 °C, the converter temperature resolution is 0.25 °C.
3. On-chip cold junction compensation.
4. High impedance differential input.
5, Thermocouple disconnection detection.
6, The working voltage range is 3. 0 ~ 5. 5V, working current 50mA.
8. Operating temperature range is -20 °C ~ 85 °C.
9, 2000V ESD signal.
Module Interface: GND VCC SCK CS SO
Supply voltage: 3~5V DC
Module size: 30mm*15mm(Length*Wide)
Package including:
2 * MAX6675 Module
2 * K Type Thermocouple Sensor
2 * Cable Line


PahanW
Reviewed in the United Kingdom on March 28, 2025
Does the Job, coupled with K type open juction thermocouples from RS, reasonably accurate, good value for money
Jonathan
Reviewed in the United Kingdom on January 7, 2024
After some issues with the adafruit libraries it works well, Nice solid thermistor provided
Alexandre Gauthier
Reviewed in Canada on September 28, 2022
Il y a une des amplis qui ne fonctionnait pas du tout et l’autre est très mal calibré. Elle a environ 7 degrés de plus.
michael schoenert
Reviewed in Germany on January 27, 2022
Das Max-Board funktioniert mit allen Thermosensoren Typ K prima, nur sind die Sensoren, die im Lieferumfang enthalten sind, absoluter Schrott.Ich steuere mit der Platine einen kleinen Brennofen, beim Test habe ich parallel dazu die Temperatur mit einem Messgerät überwacht.Die mitgelieferten Sensoren reagieren sehr, sehr langsam und hatten innerhalb kurzer Zeit Abweichungen von >150°C. Selbst beim Abkühlen, wo die Temperatur sich nur sehr langsam ändert wurden Abweichungen von >60°C und mehr festgestellt (bei 500°C).Das ist für eine Temperaturführung natürlich nicht hinnehmbar.Mit einem anderen Thermosensor Typ K funktioniert die Steuerung jedoch prima.Fazit: Max-Board Daumen hoch, Sensoren in die Tonne.
Max Schryver
Reviewed in the United States on April 9, 2021
Package did not contain the two units as described. Other reviews also do not seem to be factored into the main page showing 4.5 stars
Charles M. Ihler
Reviewed in the United States on September 12, 2020
This product works fine. The readings at 1/2 second intervals wiggle around about 0.75 deg C. But the average matches my Fluke 54 right on.The threaded post on my sensor is 6mm.Warning: Arduino users: Do NOT use the Adafruit library with this. It doesn’t work. Use the hardware spi library called “MAX6675 Thermocouple” it shows up in the standard library manager. I suspect this was some of the issues the other negative reviewers had.
Rita
Reviewed in the United States on August 19, 2020
This product is falsely advertising a K-Type thermocouple. I did not receive a K Type thermocouple. It's either T or J, and either way does not work with the included MAX6675. The MAX6675 appears to be an okay generic breakout, but will not work with the provided thermocouple. Don't waste your money.
Dan
Reviewed in the United States on March 6, 2020
One of the breakout boards did not function at all. The other gave readings that were around 105 F while an Omega HH12A said room temp was 75 F. I tested both boards with both thermocouples and with the Omega's thermocouple, and with two different Arduino sketches, all getting these same results.
Boilermaker
Reviewed in the United States on March 18, 2020
One module returned NAN the other returned 0c. Tried swapping the thermocouple but same results. Interestingly one of the modules the actual MAX6675 chip instantly got very hot.
Customer
Reviewed in the United States on October 31, 2020
I need two inputs for my project. One Thermocouple Board works, the other does not. I swapped wiring and the problem stayed with the BOARD. I swapped sensors and the problem stayed with the BOARD. One of the two BOARDS is bad. Also, one of the Thermocouple wires is not connected to the spade lug connector correctly, if I move it, the signal goes to either "NAN" (no signal) or maximum which indicates Full Scale Burnout. Pulled the spade lugs off and wired directly to the terminals on the board and the Thermocouple has a solid signal. I will be glad to change my review if a replacement board and replacement Sensor are sent by the supplier.