Your cart is empty.
Your cart is empty.80731-JX30C Well Auto WINDOW LIFT MOTOR Front Left-Driver side-6 Pin Compatible With 2009 2010 2011 2012 2013 2014 Cube S,SL 1.8L 2011 2012 2013 2014 2015 2016 2017 Juke Base, Luxury, Nismo, Nismors, S, SL, SV 1.6L 2011 2012 Leaf 80731JX30C
Joshua M.
Reviewed in the United States on June 25, 2024
Install wasn’t too bad and it works perfect in my 2010 Cube. Nissan wanted over $400 for this
Customer
Reviewed in the United States on June 16, 2024
Great price quality part.
Lacie Mohlman
Reviewed in the United States on February 7, 2024
The media could not be loaded.
Carlos
Reviewed in the United States on December 10, 2024
This motor was the perfect fit for our 2013 Nissan Juke. The only difference I see, is that it seems to raise and lower the window a little slower than the original. Other than that, I'm satisfied with the results.
V. Sanders
Reviewed in the United States on September 13, 2023
This was a great fit for a 2011 Nissan Cube. I replaced the window motor on the front driver’s side. Worth every penny.The tools I used were a phillips and slotted head screwdriver, 10mm socket (I used an impact driver, but a normal socket wrench would be fine), a trim removal tool (maybe not necessary), gloves, zip tie, and a t25 torx bit.Install (I kept my window up during the install)There are some good videos on YouTube for this, but I’ll give some details here in case it will be of value to someone.1. Remove screw in door handle with phillips screwdriver.2. Remove door switch housing. Pull back and up. Can remove switches from housing but it’s not necessary.3. Unplug wire connectors on back of switch. A slotted screwdriver makes this much easier.4. Remove the door corner panel (the black triangle piece in the front of the window). It just pulls off. It’s held in by two clips.5. Remove door panel. Pry (or pull) out to to release the door panel clips. Lift up to remove the door panel.6. Remove the arm rest bracket using a 10mm socket.7. Disconnect the speaker connector.8. Peel back the top and sides of the door air dam. I let it hang down because it wasn’t in the way and didn’t reach the ground.9. Disconnect the motor from the electrical connector.10. Remove the 3 bolts (10mm) that hold the part of the regulator that holds the motor. It will stay in place held by two brackets that hook it to the door.11. Remove the 4 bolts (10mm) holding the regulator.12. While holding the regulator with gloved left hand, unhook the part of the regulator that holds the window motor.13. Slide the bottom of the regulator to the left of the door. The window should stay rested in its track but be tilted. The top right corner of the window will be near the top center of the door track. You can use some tape here for some added piece of mind to keep the window in place. This should give you plenty of clearance to remove the old motor from the regulator.14. Remove the old motor with a t25 torx bit or driver.From here, you should be able to reverse the process. Note: the connector on this motor is attached to a long series of wires while the original was attached to the motor, so make sure to zip tie the excess where it won’t get in the way of the window. Before you hook up the new motor I would plug it in and test it. Would hate to get the whole thing put together to find out you had a dud. I would also test it again once the regulator is fully reinstalled. Also, remember to reinstall the clips in the door panel if any of them remained in the door when you removed the door panel. Nearly all of mine did.Install was much quicker than I expected: 30 minutes to an hour. Save yourself some money and tackle this job yourself. You can do it!
Mike Jansta
Reviewed in the United States on August 15, 2023
I was able to install this in my kid's Nissan Cube driver side door in about an hour without disassembling the entire regulator, etc. and it works great. Was going to cost $1K to get fixed at the dealership and auto parts stores I checked had this part anywhere from $175 to over $600...so crazy. Got this in 1-day and installed in one hour with mini socket set and screwdriver...so easy. Only needed to unscrew the 3 torx screws inside the door frame holding the motor to the regulator and the 3 bolts on the door frame attached to the regulator itself to remove the old motor and replace with the new one. If you feel tentative, look for a video on YouTube as there are a few pretty good ones showing how to do it.
JTOUMA
Reviewed in the United States on March 18, 2023
Easy to install after watching some youtube Videos. Better price for the same part you will buy at the dealer and local retailer. I would buy again if I need to.
Andre
Reviewed in the United States on February 27, 2023
The window lift motor works as promised! Priced very good! Thank you!
Recommended Products
