Your cart is empty.
Your cart is empty.Product Description
EANOSIC 1/4-Inch Shank CNC Up/Down Cut Compression Spiral Flush Trim Router Bit with Bottom Bearing
- Sturdy Durable: The compression flush-cut router bit is made of premium carbide according to stringent Industrial grade quality standards provide tough, resists wear and high cutting performance.
- Sharp Efficient: The compression flush trim spiral router bits is sharper and stay sharp longer than conventional flush-trim router bits. Provide better chip evacuation, less heat buildup, and cleaner edges.
- Smooth Stable: The up down cut bearing bit uses a ball bearing pilot at the tip to run against your project template ensure smooth running.
- 2.5X Ultra-long Life: The Blue Nano nAco Coating provide heat resistance and wear resistance,enseure great performance and provide up to 2.5X tool life
- The compression spiral router bit suit for CNC router and any plunge routers with 1/2" collet.
Professional Bule Nano nAco Coating - 2.5X Longer Life Compared to Uncoated Bits
- Blue nano nAco coating Series Router Bits utilizes a special unique carbide with composite coating for a longer lifetime (up to 2.5X longer life compared to uncoated bits) in modern materials.
- Nano blue coating enables the tool's cutting edge to retain crucial sharpness and lubricity. This provides longevity and produces cutting results of the highest quality.
- Coating prevents high heat and oxidation which is detrimental to cutting tool performance.
Mark Peterson
Reviewed in the United States on March 31, 2025
This is a beast of a bit. So far so good. It removes material with ease. Just pull back on the speed to avoid friction burning of the wood.
Andrew
Reviewed in the United States on January 6, 2025
Used this with a template for routing a guitar body (of sorts). Heavy duty and was more than up for the job. I can’t speak to longevity but no issues with one walnut guitar blank.
RB3
Reviewed in the United States on January 22, 2025
I wanted to like this cutter; it looked sharp and like it would perform well. However, the bearings on the cutter I received are not mounted concentric with the cutter body and the cutting flutes. The bearings have ~0.016" (0.4mm) runout. They visibly wobble when rolled on a table or flat surface. There must have been a manufacturing issue when grinding the mounting for the bearings, as the rest of the cutter was perfect.I didn't even try to use it; I returned it and purchased a different brand.
John
Reviewed in the United States on February 9, 2024
I can't say how long it is going to last but works much better than the traditional straight-blade flush trip bit. It reduced the grabbing and kick-back on harder woods like 3/4" thick maple.
Zack L.
Reviewed in the United States on February 19, 2024
Worked great on my first project. Clean cuts and razor sharp with clean edges. That piece however was only about 1/2inch thick and a total of maybe 20" of total cutting. Tried it on the same type of wood today but I maxed out the cutting edge at just under 2" and it's just not getting the job done. Worked ok for the first half of the plank but now it's seemed to have dulled out and producing dust no matter how I adjust the RPMs. I originally purchased this bit for a smaller project and its 1/2 diameter for getting into tighter corners but now I'm wishing I'd gone with a bigger bit after all. Also thought the edge would of lasted much longer for a $62 bit.
Melmom
Reviewed in the United States on July 20, 2023
The media could not be loaded.
shehab saeed
Reviewed in the United Arab Emirates on June 19, 2023
all good
Gary Mundhenke
Reviewed in the United States on May 7, 2023
This bit is great for flush trimming. The 1/2 inch diameter is very stable with absolutely no deflection whatsoever. I so far have used it on some of my harder woods - white oak and hard maple, and it trimmed both of these without any problems. And it left a great finish on the edge that required very little sanding.
Jonathan
Reviewed in the United States on May 25, 2023
Good price/value for a bit of this type and it worked for what I needed it to do but was hoping for cleaner edges. Had to do more sanding than expected to clean up the edges. I wouldn't recommend for high end furnishings/cabinetry.
Recommended Products
$59.66
$ 30 .99 $30.99