Your cart is empty.
Your cart is empty. 45V67 G&C Together Nipple Gas & Power cable Adapter WP-26 TIG Welding Torch Ref NO:45V67
Quantity: 2pcs
Mik
Reviewed in the United Kingdom on February 26, 2025
Not sure it's the part I wanted
db
Reviewed in the United States on March 21, 2024
I got these cable adapters to make some TIG handles for use with a resistant soldering unit I am building. These will allow me to connect the silicone wire to the adapter and then will thread onto the tig torch handle. These are great quality and much better than some others I have bought in the past.
racersdad04
Reviewed in the United States on August 22, 2023
Hose busted at the torch. These saved me a lot of money. Very easy to install but you need a proper crimper which I had.
Colin
Reviewed in the United States on August 2, 2023
This adapter is in the upper left of the photo. Perfect for connecting my new CK #17 torch to my machine.
bob
Reviewed in the United States on March 16, 2022
Works nice and flows good
Canyon
Reviewed in the United States on November 13, 2022
Needed this for my argon hose on my tig torch for my CT2050 Yes Welder. Only one I could find with the correct metric threads. Shipment took awhile as it came from China.
Tomas Grim
Reviewed in the United States on March 12, 2021
upgraded my Eastwood 200 Tig with this fitting.
ガバメント大好き
Reviewed in Japan on March 1, 2021
絶縁カバーが ズレてスパークした パワーケーブルをメンテ 出来る最高です ですが取り付け箇所のネジのパーツが付属していないのが 残念です 取り付け箇所がスパークしたパワーケーブルのメンテが必要でした。 なので 星🌟🌟🌟
Jeff K.
Reviewed in the United States on December 13, 2021
This M16x1.5-to-barbed adapter worked great for me. I had to adapt a 7/8" TIG torch (CK26) connector to my Weldpro TIG welder, which has an M16x1.5 torch port. To do that, I used this barbed adapter in combination with a 7/8" to DINSE-50 adapter for power. Works great! No issues with gas flow. For reference, the barbed end of this adapter seems to be about right for a 1/4" rubber hose.
BLANC
Reviewed in France on May 19, 2020
Le pas de vis ne s’adapte pas au branchement du tuyau orange silverline 8 mm, je recherche un embout mâle gaz car j'ai une panne de soudeur zinc expresse avec un branchement tétine et je ne voudrais pas couper le tuyau orange silverline 8mm, avec de l'autre coté une tétine pour un branchement en8mm sur le tuyau silverline acheté précédemment.
あかし
Reviewed in Japan on May 13, 2020
よかった
ルアーマン
Reviewed in Japan on July 20, 2019
国産プラズマカッターを持っており、純正トーチが高額なので安価商品購入。取り付けネジの互換性が無かった為購入。輸入品の為、到着までに2週間ほどかかったが安価トーチが使えるようになって助かった。あと、スイッチケーブルのコネクターもサイズ違いのを同様に注文し少しの加工で問題なく使えるようになりました。
Recommended Products
$17.99
$ 8 .99 $8.99