Your cart is empty.
Your cart is empty.
- The hair pulling task of removing wheel bearings has been made easier!
- Removes bearings without damaging wheels.
- Works on virtually any sized motorcycle wheel bearing.
- Safe and easy.
- The set consists of 7 removers-25mm, 20mm, 19mm, 17mm, 15mm, 12mm and 10mm; Plus 2 rods to fit all bearing sizes with storage case.
- Each remover has a tapered end so part of the remover will slip inside the bearing...simply put the proper size remover in the bearing, then flip wheel & bearing over so the remover is against the floor. Next take the rod tool and insert into remover and tap firmly into place (the remover has a slot in it for the rod tool to slide into). Once you have the rod firmly in place simply lift the wheel and bearing off the ground and tap again and the bearing will fall out. When the remover is against the ground and taped on, it is spread apart tight against the bearing, then when you lift off the ground and tap, it pushes the bearing out of the race. You will be able to remove bearings in seconds with this tool.
- Manufacturer offers lifetime warranty on this tool.
jamieslife
Reviewed in the United States on January 21, 2025
This tool works great. I have a BMW R1200GSA and the included 20mm insert is exactly what you need. Take your time to heat the hub. I had two 36" sections of 4x4 wood to set the tire rim on. Used one of those sections to set the drive bar into the insert. Both bears came right out. The tool is well built and great value. This tool would work well for a one off in a home garage like me or multiple uses weekly in a shop.
Customer
Reviewed in the United States on September 26, 2024
There's a number of different tools for bearing removal in my garage, however, none would work for the removal of my front wheel bearings on my BMW K1200GT due to no leverage available...until now. This tool made easy work of removing the bearings. Easy to use and gets the job done. Handy tip...spray WD40 or similar between mating surfaces and leave for as long you can before using this tool. This will brake down any corrosion bonding before attempting use this tool.
a r
Reviewed in the United States on May 17, 2024
Nothing else worked correctly on my motorcycle wheel bearings. There was no space to do the big screwdriver method. I tried the bolt through a piece of rubber, no dice. Spent some time before I ordered this. Got this, used it Even for the second bearing in the hub because it was easier than the backside socket method. Absolutely the easiest method for motorcycle hub bearings I know of.
Joe G.
Reviewed in the United States on October 7, 2024
Worked the first time and every time. Much, much easier than struggling with a flathead screwdriver.
MajorIRdave
Reviewed in the United States on April 10, 2023
It's the same price as the harley wheel bearing puller but WAY simpler and extremely tough. I only own one harley but lots of other various European and Japanese street and dirt bikes so the multiple fittings were a selling point. You can really beat the heck out of it and it holds up. When used on the 1" (25.4mm) bearing with the 25mm fitting, it barely holds and will require several attempts BUT it will work. You really have to sledge hammer the rod into it but it works and did not damage the tool at all. I would consider it 5 stars if you work on metric only, 4 stars if you also intend to use it on 1" harley. I guess in reality it is 5 stars because it did get the job done for an unspecified size.
Scott
Reviewed in the United States on March 30, 2021
This tool is made of chinesium and also doesn't work well. It doesn't grip the bearing well enough. For the same amount of money you could get a blind bearing puller kit which would work for more than just wheel bearings. Make sure to get one with a lip to help grab the bearing.That being said, I did manage to get a bearing out using this tool, but it was a struggle.
Joe Pazdera
Reviewed in the United States on May 9, 2016
I received the product in record time. Upon opening it, I was not happy to see that there were no instructions provided. After trying to use it with no results I You Tubed it and found a video that was very informative. It now works like a charm! Great product.
MJS
Reviewed in the United States on May 13, 2016
This seemed like a well constructed bearing removal kit. I was able to pull the first bearing out on my front motorcycle wheel but the second one was jammed in there really tight. Unfortunately the design that causes the rod to spread the bearing puller out to grip the bearing resulted in it basically becoming a cold chisel when I had to give it some more encouragement. It split the bearing puller in half. I was able to return the set for a full refund and I feel bad it didn't work out.If your bearings aren't pressed in super tight this should work fine. If you find you have to really pound them out be prepared for an accidental splitting of the bearing removal device. You might need one of the designs that uses a spin method of tightening the collet versus a spread method. They cost more but you might need it.
Recommended Products
$72.86
$ 34 .99 $34.99