Shopping Cart

Your cart is empty.

Your cart is empty.

Phoenix goods Urethane Bandsaw Tires 20 inch x 1-1/2 inch x 1/8 inch 2 Pack for most 20' Band Saws No Adhesive Needed

4.5 (4) Write Review
Free shipping on orders over $29.99

$53.86

$ 24 .99 $24.99

In Stock
  • Urethane Band saw Tires 20 inch x 1-1/2 inch x 1/8 inch, 2 pack, They can be installed on most 20" band saw that requires a 1-1/2" wide and 1/8" thick tire.
  • Longer belt life – Made of Urethane, The long-lasting upgrade to rubber belts, Urethane band saw tires most certainly outlast rubber band saw tires and plastic band saw tires. Urethane band saw tires will not dry rot like rubber or plastic tires. This alone provides you with an exceptional value over other types of band saw tires.From improved performance and safety to reduced downtime.
  • Fast, easy installation –no adhesive is needed for proper installation. Urethane tires are specifically designed to stay in place without any type of adhesive and can be stretched to fit. This makes them even easier to install and even easier to remove if necessary.
  • 20" x 1-1/2" x 1/8" Tire fits for any band saw that needs a 20" x 1-1/2" x 1/8" tire. The actual wheel diameter can be 19-5/8″ to 20-1/2″ in diameter.
  • The surface is specially treated, more slip resistant than others Urethane Band Saw Tire, only Phoenix goods supply, All of this improves blade tracking and extends the life of your blade. urethane tire installation process is quicker and easier for increased productivity and efficiency. And, these tires are bright orange,which makes them super easy to inspectcess is quicker and easier for increased productivity and efficiency.


Urethane Bandsaw Tires 20 x 1-1/2 x 1/8 IN, 2 Pack

How to install

First, After disassembling old "tires", clean up the gummy debris left on the wheels.

Mounting:

Used a clamp to hold the tire on the wheel in one spot, and then used a screwdriver to pry the rest of the tire on. This made installation relatively easy

Uniform stretch:

After mounting, removed the clamp and pushed the shaft of the screwdriver completely under the tire, so it was between the tire and rim. Then ran the screwdriver around the wheel several times to make sure the tire was uniformly stretched around the wheel.

Seating the tire:

Next, made sure the tires were properly seated in the groove on the wheels, rolled the wheel on a concrete floor, pushing down pretty hard with your hands, so the concrete would forced the tire into the groove.

After mounting, reinstalled the wheels and readjusted everything, finish!

✅Urethane band saw tires no adhesive needed, but need to be stretched on. If your new band saw tire is too tight to fit onto the wheel, submerged the new tire under hot water for a few minutes, this will make things easier.


Jameson c.
Reviewed in the United States on January 6, 2023
Update to the below earlier message: the drive wheel tire broke at 11 months. See picture.,..Earlier message: These are NOT injection molded; they have a seem that was then supposed to be ground down by the manufacturer. Apparently their quality control is poor at best because the ones I received were BOTH ground down too far as you can see in the picture making my blade skip back and forth instead of staying centered…. Bad deal for 60+ dollars. I even tried them inside out and same thing; the seam area is ground too far…
tomas
Reviewed in Mexico on April 30, 2023
Lo uso en una sierra jet, es 1/16" mas grande pero no es necesario recortar, funciona muy bien
TerryCats
Reviewed in the United States on November 1, 2022
N/A
Michael Wells
Reviewed in the United States on February 2, 2021
The item fits the description