Shopping Cart

Your cart is empty.

Your cart is empty.

MoKitDora Handlebar Extended Wire Harness CAN-Bus Switch Wiring for Harley Softail Touring Dyna Sportster Models 16 Inch

Free shipping on orders over $29.99

$27.99

$ 13 .99 $13.99

In Stock

1.:8 Inch


2.Color:Black


About this item

  • Fitment - The handlebar wiring extensions fit 2011-up Softail, 2012-up Dyna, 2014-up Touring, and 2014-up Sportster Models
  • Easy to Use - The Touring handlebar CAN-Bus wire extension harness can plug and play, with no cutting needed to install, saves complex wiring work and avoids switch damage due to a wrong connection. The connectors are also small enough to go into most handlebars for ease of hiding wires
  • Practical Utility - CAN is a two-way communication network that does not require the large number of wires used in previous models. These wiring harness extensions are used when you are installing a taller handlebar and need to extend the CAN wiring harness
  • Quality Speaks - The Softail Can-Bus wire extension kit is High quality and very durable, the connection is safe. The connection is tightly locked to reduce the possibility of breaking the wiring harness. The wire extension harness is both safe and convenient to use
  • Customer Support - Comes with wire extension harness as the picture shows, instructions are not included. Back-up with 24/7 customer service, if any questions you have, please message us to get a good solution.



Product Description

WIRE

Dear Customers,

WIRE

Fitment

Fits 2011-up Softail, 2012-up Dyna, 2014-up Touring, and 2014-up Sportster Models.

Size: 8 Inch, 10 Inch, 12 Inch, 14 Inch, 16 Inch.

Fits the 2017 HD Freewheeler.

WIRE

Installation Instruction:

1. Disconnect the battery first, not to cut and solder can/bus wiring whatsoever.

2. When replacing your handlebars, locate the new, very small (black) 4-position male and female connectors located under the front of the fuel tank.

3. Once found, disconnect the male and female connectors.

4. The male connector is attached to the main wiring harness and the female connector is attached to the handlebar switches.

5. Now simply re-connect, using our extension wiring and be sure the connectors are seated properly and cannot be pulled apart without releasing the lock.

6. Before completing your installation, reconnect the battery and test all switch functions.

DETAILS

plug and play

DETAILS

safely connected and tightly locked

DETAILS

small enough to go into most handlebars


kent devoe
Reviewed in the United States on February 11, 2025
Very easy to install
LEONARD
Reviewed in Canada on April 15, 2024
I was adding extra led lights and needed pin connection, in ordering and cutting in half was cheaper than buying the plug and pins,In the pass I also purchased a splitter this is were I added the extra lights to. I don’t like cutting any harness
F350Mike
Reviewed in the United States on September 15, 2023
Used to extend cables on a 2023 Harley Tri-Glide. Cables arrived when advertised. Install was easy. Worked as expected. Perfect fit and function. Zero issues.
Customer
Reviewed in Canada on July 27, 2023
This made the job of putting on higher handle bars so much quicker and easier than splicing the wires. And forr the price- it was well worth the ease..
Dan
Reviewed in the United States on March 11, 2023
No issues with any plugs, does the job and is made of quality and durable material
Jerry A. Brown
Reviewed in the United States on February 8, 2023
Very good canbus wire terminals.
Merk
Reviewed in the United States on January 6, 2023
Used these when upgrading to 12” Factory 47 bars on my 21 Road Glide. Made for a clean look
Jeffrey
Reviewed in the United States on August 31, 2022
did not use because it was only for turn signals.
Customer
Reviewed in Canada on December 10, 2022
Ça ne va pas après un flhtc 2012
Recommended Products