Your cart is empty.
Your cart is empty.Product Description
The versatile, compact 18-inch (46 cm) drip edge folding tool makes quick bends along the drip edge of flat-pan standing seam metal roofing panels. Two rib-reinforced steel plates are permanently welded together to create two folding seams for making 1-inch (25.4 mm) and 1-1/2-inch (38.1 mm) deep bends in maximum 22-gauge (0.76 mm) steel. A two-post-design, fiberglass reinforced nylon handle offers durable, lightweight strength and high leverage for working overhead or on a bench.
From the Manufacturer
Versatile, compact 18-inch (46 cm) drip edge folding tool makes quick bends along the drip edge of flat-pan standing seam metal roofing panels. Two rib-reinforced steel plates are permanently welded together to create two folding seams for making 1-inch (25.4 mm) and 1-1/2-inch (38.1 mm) deep bends in maximum 22-gauge (0.76 mm) steel. A two-post-design, fiberglass reinforced nylon handle offers durable, lightweight strength and high leverage for working overhead or on a bench.
barnis07
Reviewed in the United States on July 30, 2024
Perfect tool!
MasterTech
Reviewed in the United States on February 20, 2024
I purchased this to hem some 16 inch standing seam roofing for an awning I built. I could not find this tool in the correct width for my project so I bought this 18 inch one and cut it down to fit. It worked perfectly and cutting it down caused no issues with the tool. I would say 15-7/16 inches is about as narrow as you can go on this tool without cutting into the handle.
Easy-Going
Reviewed in the United States on November 21, 2024
Works great but the handle is annoying, so I took it off. Much better.
Kakunka
Reviewed in the United States on October 26, 2024
I like the large easy to grab and leveraged handle. . . Sure, you can buy the little metal blade version for less than half the price, but there's no handle, and leveraging the little blade is a little bit of a trick. . .Pay the extra buck, and don't give yourself carpal tunnel . . .
WILLIAMKRAFT
Reviewed in the United States on September 15, 2023
smart little tool to have for your bending needs
TR
Reviewed in the United States on July 4, 2023
quality tool, i get great results
Scott
Reviewed in the United States on June 13, 2023
Installing my 1st stand seam roof. If you’re going to wrap the ends of your panels around the drip edge, this tool is essential. I’ve only used the one inch side of this tool. It makes perfect, controlled bends. I’ve dropped this tool a bunch of times from a saw horse down to the garage floor with no bent corners. This tool is well made. When I was shopping for a bending tool, there were lots of tools contractors used, online. I’m really glad I picked this one. Tip: I also bought a Malco 6” wide hand seamer. High quality and essential, also.
TerraVie
Reviewed in Canada on October 9, 2022
Utilisé pour plier les rebords de bardeaux de métal.
Jennifer
Reviewed in Canada on January 9, 2021
Great
ase floris
Reviewed in Canada on July 26, 2020
Perfect tool for installing a metal roof
Oxford Metal
Reviewed in Canada on February 16, 2019
Folded 24ga standing seam panels for weeks on end. Great tool
james
Reviewed in Canada on December 22, 2018
Works great for doing standing seams and bigger corner bends. My only issue is that I use 26g metal and the slot is a bit thicker so the 2 corners dont always fold perfectly on the line. Making me have to tap the corners in. Other than that great product. Handle makes it much easier on longer bends.
Michael B.
Reviewed in the United States on January 22, 2017
This is a must-have for chimney flashing! I used this to bend the lip on cap flashing. It is soooo much easier to make small bends right there on the roof, saving many trips up and down the roof. With a little care, It's long enough to easily bend galv. flashing 3 or 4 feet long and small enough to toss in the tool bag. Nice and sturdy, I expect to get many years service out of this bugger!
Recommended Products
