Your cart is empty.
Your cart is empty.Product Description
David traver
Reviewed in the United States on September 1, 2024
Was fast receiving and great product .
Wagner family
Reviewed in Canada on August 10, 2017
pleased with product
Willie300s
Reviewed in the United States on July 26, 2017
I have noticed that there are a lot of comments in these reviews that do not apply to the FS-iA6B receiver and are therefore misleading.I have purchased 2 of these receivers to use with my FS-I10 transmitter and they are really great. Bind quickly and have excellent range. The construction is also excellent, on par with Futaba and JR. I now have 6 models flying on my new FS-i10 and have had zero problems. The programming is extensive and simple to implement, in many ways far ahead of Futaba, JR and Spectrum (and in some ways not so much). I would expect that future upgrades will fill in any missing features such as voice and quadcopter support.
Drone Man
Reviewed in the United States on March 8, 2017
Works great. Pairs with drone and my Flysky Transmitter. You have to make sure to be careful when you short the two power leads together to complete the circuit. That you have the PPM wire facing the correct way.(which is actually upside down if you hold the receiver right side up). If you put the wire in with the incorrect + and - poles, you can easily damage the receiver. It will start smoking and burn up your receiver. So research before you install. Once you have the power pins shorted and your ppm wire installed into receiver correctly.(make sure the antenna is on B4 you ever turn on Drone). Then put the battery in your drone. You must hold down the bind key on your transmitter. And then turn on the transmitter. The transmitter should say bind ok. Then you remove the bind plug. Don't forget to program your transmitter for PPM and set adjust your Flying. Thanks. Your Fellow Drone Enthusiast.
Rory Forsythe QuadGod
Reviewed in the United Kingdom on March 12, 2017
The fact you can use ibus or sbus or even ppm,is handy and that it'll bind with my turnigy evolution,makes it good for converting some older quads over to the evolution.Good performer,no brown outs,and does what it is designed to do adequately.
Cliente
Reviewed in Italy on February 14, 2017
Ottimo pezzo, io ho una turnigy tgy i6 e sono riuscito a bindarla senza problemi.ottimo acquisto, anche se arriavato con prime 5 giorni dopo
Customer
Reviewed in the United States on January 19, 2017
I was excited to try I-Bus with this new rx. I-Bus worked great, but the rx never powered up again after a pretty small crash. Probably fine for wing use but not durable enough for quads. I've moved on to another flysky rx that supports I-Bus and hopefully its more shock resistant.
alessandro
Reviewed in Italy on September 2, 2016
ho un telecomando eachine i6.....siccome come fattezze era identico a quello della fly sky ho pensato che questa ricevente potesse andare bene con il telecomando eachine i6 e cosi è stato funziona perfettamente......
LTandMR
Reviewed in the United States on August 29, 2016
Works great with my CC3D Flight controller on PPM with the FlySky Fs-i6 transmitter. I have seen them cheaper but not with 2 day shipping!If used with CC3D the black wire #8 connects to PPM port then the 3 wire (white/red/black) connects to another input for powering the receiver, Don't forget that! I used the 90*antenna mount that comes with the CC3D but had to zipty these antenna onto it versus running inside the tubes! I recommend getting a 90 degree antenna mount and having it mounted lower than your props so the leads are protected from the props! Always run 2 wire antennas at a 90 degree angle to each other to be sure it can grab the signal from transmitter!
R Crosier
Reviewed in the United States on March 25, 2016
Works great with FlySky FS-i6 transmitter! I use this with a Hobby King HK32Pilot (pixhawk clone), and it works great. Uses one wiring harness to connect to the pixhawk/hk32, so you do not need a PPM encoder to use it with them. Just configure your TX to use that, and you're set.
Kunde
Reviewed in Germany on February 15, 2016
Top.Leicht zu Binden mach auch gute Arbeit. Was mich stört sind die Antennen selbst was so ein Dickes Teil am ende draufhaben was auch immer das sein soll.Verarbeitung auch recht gut.Gern nochmalMfg.
Jason
Reviewed in the United States on November 15, 2016
This is a great receiver, but i'm a bit disappointed how big it is. would really like FlySky to make a smaller receiver with PPM. This is a good receiver, and worked well, but I needed to return it because it does not fit well in my 210. As much as I'd like to use this receiver I'm stuck with the FS-ia6 for now.
J. Steven Barrett
Reviewed in the United States on November 29, 2015
No issues with this other than operator (idiot moment) error and chopping off the antenna wires with a prop strike. Ah well, live and learn. It did give me a great excuse to order a couple more... The PPM on this is great, one signal wire and all channels are available, sweet. I've seen no glitching and range seems to be AOK.
Recommended Products