Your cart is empty.
Your cart is empty.Window motor worn out? This power window lift motor is precision-engineered to match the fit and performance of the original motor in specific vehicle years, makes and models for a reliable replacement. This part is compatible with the following vehicles. Before purchasing, enter your vehicle trim in the garage tool to confirm fitment. [Dodge D150: 1990, 1991, 1992, 1993] - [Dodge D250: 1990, 1991, 1992, 1993] - [Dodge D350: 1990, 1991, 1992, 1993] - [Dodge Ramcharger: 1990, 1991, 1992, 1993] - [Dodge W150: 1990, 1991, 1992, 1993] - [Dodge W250: 1990, 1991, 1992, 1993] - [Dodge W350: 1990, 1991, 1992, 1993]
Ian Murray
Reviewed in Canada on May 29, 2023
When installed my window goes up and down much faster than it did before. The only problem I found is that it does not have one of the brackets needed to brace it to the door. Although it works great with the door panel off I can see some movement. Would benefit greatly from the original bracket being included on the part. It's probably done this way so it will fit more applications.
kian
Reviewed in Canada on October 1, 2023
It is not fit to dodge van 2000, while it described writen was Fite.
Jared Searle
Reviewed in the United States on April 14, 2023
It works but I had to extend the wires and get different bolts because they are metric not standard
jojo
Reviewed in the United States on April 21, 2020
Worked great for a few years then started acting up. Pulled it out and compared it to the original. Dorman fails to drill drain holes like OEM in the motor housing and it filled up with water/moisture causing the permanent magnets to separate from the case and render unit inoperable. Another fun note. In the winter it will stop working when the water in the motor freezes. If you buy make sure to add drain holes.
ken
Reviewed in the United States on May 3, 2019
Motor is smaller dimensions than original , can't use end support on motor so door flex's when window is closed , had to grind drive gear to make fit in guild hole , works good , cheaper than old style
Viola Soffe
Reviewed in the United States on October 8, 2019
Came quickly. Easy to install. Now company does not sell parts for 13 year old mower
Brett butler
Reviewed in the United States on September 18, 2017
It said this product would fit my 1992 dodge W250, however it did not nor did it come with any special instructions for retro fitting it. It didnt ihave the stud hole in the gear, please see pics. In the pic is the driverside one which i will be sending back.
Jreich
Reviewed in the United States on May 24, 2017
It fit and had the same plug as the previous motor, although the wires were reversed. It wasn't a big deal to change the connections within the plug.The previous motor had a bottom brace in addition to the 3 self tapping bolts holding the motor. So far it works fine without that brace. No way to attach the old brace to this new motor.
Master
Reviewed in the United States on October 16, 2017
I liked it but I have a Dodge Ramcharger and it was more than hard to get in 😂The stock 1990 Ramcharger comes with a brace at the bottom to hold the pointy end part in the downward position and with this one you have to simply turn it upwards to get it to catch on the inner gears of the window control arm.This model doesn't come with a metal gasket to hold it in place use your stock one and flip it into position.Wiggle it around until all holes are aligned properlyExtra notes.1. you'll have to grind off the three centerpunch nails that hold the original in place. And remove the three bolts.2. There's a factory cutout with a bolt in it on the top left of the inner door you'll have to bend the metal that it is bolted on upwsrds.Other than that it does help to have two people and a flashlight.
whywhy
Reviewed in the United States on August 16, 2012
Motor worked flawlessly and was quiet.To install be sure to tape the window in place. After removing the orginal motor, which involved removing the 3 mounting screws and a screw on the bottom,this motor installed in the same place. Just use your original screws (they are self taping) and don't worry about the the bottom screw that the original motor had,it doesn't appear to be needed.
Recommended Products
$83.26
$ 36 .99 $36.99
$47.67
$ 23 .99 $23.99