Your cart is empty.
Your cart is empty.These wheel lug studs are made of carbon steel and tested to demanding automotive industry standards to ensure strength, longevity and safety. This part is compatible with the following vehicles. Before purchasing, enter your vehicle trim in the garage tool to confirm fitment. [Pontiac Vibe: 2003, 2004, 2005, 2006] - [Toyota Matrix: 2003, 2004, 2005, 2006]
K
Reviewed in the United States on March 8, 2025
ALL 30 ARRIVED! ORDERED 3 PACKS.
Ravi
Reviewed in the United States on December 27, 2023
Bought of set of studs made in C***a that snapped while driving at low speeds. Replaced with these and no issues.
Gabriel J. Lopez
Reviewed in the United States on March 24, 2022
Arrived right away and worked perfect for my Lexus RX 300. I installed extended studs so I could run wheel spacers.
WC
Reviewed in the United States on March 16, 2022
I upgraded the wheels on my Pontiac Vibe, but noticed that the front wheels studs did not have much room/thread for the new wheels. I was really worried about it so I did some research and it is apparently a common problem.... so I ordered these and have changed wheel studs before so I thought it shouldn't be so difficult... well that was a yes and no, I've changed studs on Honda's, and you always have to grind part of the hub to remove the stud and install the new one. I was pleasantly surprised to find that the Vibe (Toyota Matrix really) had a notch in the hub already, so it made removing the original studs easier than I expected.HOWEVER... since I was installing these extended studs, I wound up having to grind the hub in order to get the longer studs to fit... If I was just replacing the studs with the same factory size ones, it would have been pretty straight-forward and would have fit in the existing notch, but since they are good amount longer, they do not line up with the notch in the hub properly.... I just thought I would mention this so that anyone that is planning on doing it themselves can at least prepare for it.
Cristian Alvarado
Reviewed in Canada on October 11, 2019
Product good. Needed ten but they only had one and the description was misleading
Rkr8
Reviewed in the United States on July 10, 2018
Should of been 10 in the box. Only received 9. Other than that, product seems to be what I needed, just not enough shipped.
Mathieu
Reviewed in Canada on April 13, 2018
Le produit est correct, mais j’ai reçu un seul et non 10 comme supposé être selon le numéro de pièce.
Customer
Reviewed in the United States on September 19, 2017
$27.50 for (1) stud?! Listing and previous reviews advertised as being sold in quantities/boxes of (10). With local parts stores selling these for $3 ea, that made sense. I needed (12) for my application, so I bought a qty of (2) figuring I'd get (20) studs. I received (2)! Warning to any future buyers, don't waste your time on these....
Christopher
Reviewed in the United States on March 23, 2016
I recently swapped out the factory steel wheels on my '09 Tacoma 5-lug for a set of alloy aftermarkets that fit well, except they're a bit thicker than the originals. The lug nuts I'd been using were angled and overall were threaded sufficiently onto the studs to be "safe," but the factory wheel studs ended inside the studs. After digging around on a number of the forums I came across these Dorman studs and decided to try a box of them (all of the specs are the same as factory, except these are ~0.55" longer, perfect for this application).I almost wonder if the other reviewer had a bad batch of these, or maybe put them in dry. I used a little anti-seize on the shoulder and knurling of the studs to ensure they went in smoothly, then installed them using a stack of M14 washers (large enough to go over the shoulder), an M12-1.5 nut, and my impact gun. Installation was quick and easy and so far so good!
GBC
Reviewed in the United States on October 6, 2014
These come in a box of ten studs. Two of them broke when installing wheels so I had to buy replacements at a local parts store.
Recommended Products
