Your cart is empty.
Your cart is empty. Detailed specifications about bearings
Bore Diameter: 3/4"
Outer Diameter: 1-3/8"
Inside Ring Height: 1/2"
Outer Ring Height: 7/16"
Flange Thickness: 5/64"
Flange Diameter: 1-1/2"
Limit Dynamic Load 1500 Pounds
Limit Dynamic Speed 4600 rpm
Perfect Fitment : Widely applied in lawn mower, wheelbarrows, garden carts, hand trucks, pressure washers, generators, air compressors and more.
Replacement for Brand and Models:
532009040, 13359, 9040H, 532124959, 5920H, 9040HR, 9040N.
Marathon 60611, 60011, 60010.
Ariens 05408900, 05416200. Bobcat: 2188123-03.
Bunton P0209, PLO941.
Case 384881-R93, 384881-R94, C12110.
IH384891-R94, 384881-R93, IH384891-R94, 05408900.
Gravely 011193, 036778, 05408900, 037823.
John Deere 941-0141, AM118315, AM127304, AM35443.
MTD 741-0141, IH-384881-R94, 941-0141.
Snapper 1-0953, 1-2390, 1-5474, 2-6693, 7028722, 7028722YP, 1305379.
Toro 110513, 251-210.
Easy Installation and Say Goodbye to Low Efficiency
Just taking out the damaged bearing and putting a new one in the right position, the machine can work efficiently again, greatly saving your time and energy.
High Quality
Double seal on both sides effectively save grease and stop impurities and contamination from entering, extending the life of machine.
Made of bearing steel and the lifespan is longer than carbon steel, saving you maintenance costs and avoiding frequent replacement.
Roy J.
Reviewed in the United States on January 24, 2025
Upon receiving these bearings, I pulled both dust shields, front and back off of the bearings. Of the ten bearings, 5 had no grease at all and the other five had a little grease on one side. I packed with a good bearing grease in both sides and replaced both dust shields. To grease all the bearings, it took about 30 minutes. Without grease these bearing would not last long. Work good and are holding up on my wood cart after greasing them.
ATIMATIK
Reviewed in the United States on January 15, 2025
I seriously went through my entire set of 10 bearings as every single one failed! The inner races always crack and fail making the whole bearing blow out, and did so in short order every single time!! JUNK.
Charlied
Reviewed in the United States on August 19, 2024
I am always repairing garden equipment . These are great for wheels ! Now I don’t have to run to town when I need one !
TMP
Reviewed in the United States on June 5, 2024
These have some wobble play but nothing you will feel unless you remove the grease. I would not use these on high speed applications as they have .004” tir.
Michael
Reviewed in the United States on June 1, 2024
I ordered these for a small yard trailer I have. The original bearings wore out after only two, three hour uses of hauling firewood. These bearings fit tight (which they should) in the wheels and had twice the depth of the original bearings so the bite is good. There is no way these are working their way out. I have bought this brand before in a different size (for a gate wheel) and they are doing great since being installed in January of 2024. I expect these bearings to last a long time, plus I have extra so I can replace again when needed. I highly recommend this brand!
Dylan P.
Reviewed in the United States on February 8, 2024
We use the heck out of our kids wagon (I pull an extended version of a Cartwheels wagon with 6 wheels using an electric bike), and the 20mph rides have finally worn out the bearings in a couple wheels. Figured I'd check online to see if I could source a replacement. Found these and they work great. I believe you can use this version, which is a sealed bearing design, or the open bearing version as well, though with the dirt and debris, I'd get the sealed version.I used a punch and hammer to smack the old bearing out, and a large socket and hammer to install the new one. Took under 5 minutes, including removing and reinstalling the wheel. Might be easier if you had a press, but honestly worked fine using a hammer.Overall, I'd highly recommend these. The original bearings lasted 350 miles, and I'm hoping these last at least as long.
paul turnbow
Reviewed in the United States on November 4, 2024
Perfect for replacing old rusted bearings. Easy to install.
Pillgri,,
Reviewed in the United States on October 20, 2024
Easy to replace bushings for bearings on my Craftsman LT1000
Bruce Blackstock
Reviewed in Canada on April 11, 2023
Work as they should
gaetan
Reviewed in Canada on February 25, 2022
Construction dun buggy
david
Reviewed in Canada on November 11, 2022
Pas cher et va bien
Joe
Reviewed in Canada on January 20, 2022
These bearings seem to be made well and are attractively priced. Used for one summer on my Woods RD72 mower and continued to stand-up, but time will tell if they will last.
Dave B Customer
Reviewed in Canada on December 22, 2020
Fit my marathon flat free tires perfectly. I added my own wheel bearing grease. There was a coating but I wanted more. The bearings appear to be the same as the original. They are not heavy duty. I removed the flange on 2 and pressed them into the axle of the wheel and 2 with the flange intact to replace originals, in hopes of longer life. Originals lasted 2 years of rough use.I will buy again if needed and would recommend.
Recommended Products
