Your cart is empty.
Your cart is empty.Product Description
5 3/4" Black Aluminum Headlight Grill Cover for Sportster Roadster XL1200R XL883 883 Custom XL883C/XL1200C Low XL883L/XL1200L Iron 883 XL883N
- Diameter:5 3/4" (outside diameter is 6")
- Fitment:
- for Sportster 883 Custom XL883C 2004-2009
- for Harley Sportster 883 Low XL883L 2005
- for Harley Sportster 883 Low XL883L 2010
- for Harley Iron 883 XL883N 2009-2014
- for Harley Sportster 1200 Custom XL1200C 2004-2014
- for Harley Sportster 1200 Low XL1200L 2006-2011
- for Harley Sportster 1200 Roadster XL1200R 883 XL883 2004-2008
Perfect Match
- Diameter:5 3/4" (outside diameter is 6")
- New with good quality
- No Modification Required
High Quality Material & Premium Performance
- This headlight cover is made of high-quality billet aluminum and has a long service life.
- This headlight cover is anti-corrosion, rust-proof and waterproof, which will be very good to against a variety of harsh conditions and weather
Easy to Install
- Step1: Remove the old headlight trim ring.
- Step2: Slip the new trim ring into the headlamp.
- Step3: Srew the cover to the ring.
- Tips: Because the thickness of the headlight is different, you can adjust the tightness with a tape.
Sabrina chavez
Reviewed in the United States on March 26, 2025
Value for money , and it was super easy to install
John L.
Reviewed in the United States on July 6, 2024
Looks good but it keeps getting loose. Returned.
Michael Saborowski
Reviewed in Germany on October 30, 2024
Hochwertige Verarbeitung und sehr massiv.Passt leider nicht auf mein Motorrad...
jami
Reviewed in Germany on October 22, 2024
Alles bestens danke
John blum
Reviewed in the United States on April 26, 2024
Easy to install, replaces the headlight retainer ring. Sturdy, stays put. But after closer inspection I found that it doesnt keep the actual headlight in place. the headlight its self wobbles around. impossible to keep adjustment, Whats worse is that I cant get it off now. I hand tightened it, but two of us with tools cant get it off. I defiantly would not buy them again.
Apache Man
Reviewed in the United States on September 13, 2023
You Need to take a picture once inside the bulb housing of the wiring disconnect your battery before you cut yer wires measure to be sure you have enough wire to the main bulb connector ("BEFORE YOU CUT THE WIRES") Be sure to leave enough wire to reconnect to the Bulb Harness than pull the wire from the rear of the housing ( DO NOT PULL THE RUBBER INSULATION FROM THE HOUSING ) just the wires take the Ring and place it over housing ( be sure to remove the reflector housing from the bike frame ) do this by removing mount nut to drop the fixture slide the ring to the front of the bulb and remount fixture take ring ( clamp ) from the bulb and save it, next push wires thru the tube at the back of the housing and splice your wires in the color order you cut them at, use butt connectors and cover the wiring where connected them to the bulb plug first individually than seal them so as they are covered to the plug to prevent moisture entering area over time mot the bulb spin on the ring after you set yer bulb into the receiver it wont fit if you use the original mount in housing if clamp attached set your bulb mount and enjoy.
Guillaume C
Reviewed in France on August 8, 2022
Très content de l’article. Ne pas se fier à l’emballage (simple sachet et emballage en papier journal en chinois et aucune étiquette ni notice). C’est bien de l’aluminium anodisé et pas de l’alu peint, je n’ai constaté aucun défaut de fabrication ou esthétique. Installé en quelques minutes à peine, sans même devoir démonter l’optique. A voir à l’usage comment ça vieillit et si ça tient correctement.
Michael
Reviewed in the United States on March 21, 2022
I really like the look of these headlight grilles on motorcycles. I saw the price and said why not! It more more difficult for me to take off my little fairing and put back on than it was to install this grille. Had a few set backs but I made it work. First, the two piece grille has some sharp spots so be careful. I sliced my finger on it but just wear gloves if you have soft hands. Second, fully tightened mine was a tad loose as well as the headlight so I took it off and wrapped a little electrical tape around the light housing and that plowed the grille to tighten well and is now solid with no movement. I have a 2021 iron 1200 and I managed to use this and still keep the fairing installed. See the picture. It was a tight fit though so do it at your own risk. Only time will tell is the added pressure on the mounting points will hold up. Overall this is a good item at a good price and it looks well.
Maximum
Reviewed in Mexico on February 12, 2022
Excelente acabado, necesita un trozo de cinta para que no se mueva con la vibración al conducir, no fue necesario desmontar el tanque ni el tornillo del faro, entra a presión metiendo primero un extremo y apretando la base del faro, tardé 5 minutos para instalarlo y luce muy bien, recomiendo colocar la parrilla vertical para que la luz no se vea afectada, excelente calidad.
GDPhotography
Reviewed in the United States on April 28, 2022
With a price like this, you can't go wrong. First thing out of the box, it's heavy, and sharp! They do not mess around in that factory. Because I have an LED headlight, the install was pretty difficult. You just need to twist with one hand and hold the back with the other, the trick is not slicing your fingers open when pushing on the grill. After vet glue and a bandaid, I rode off! It looked great, until I noticed the headlight was slowly but surely rotating around (Harleys DO vibrate). After getting some velcro, it's snug as can be. For a universal, affordable grill, this takes the cake! Looks absolutely amazing on my newer LED headlight.
SonicFun01
Reviewed in the United States on April 15, 2022
This headlight cover looks sweet on my blacked out Harley Sportster 48. It was super simple to install; simply removed the old chrome ring that fastened at the bottom of the headlight, then maneuvered the black base ring over the headlight housing, then screwed the black grill cover on tight. It seems very durable and sturdy, hope it holds up over time with the signature Harley vibrations and rumbles :)
Brian
Reviewed in the United States on June 20, 2021
Great addition to my 2016 Harley Sportster 48! It made the whole front of my bike look different. some have said this was hard to install or wouldn't tighten. I had no issues with this. You dont have to unplug the stock front headlight or wires to install. Just tske stick headlight ring off, then slip this over everything at an extreme angle and put back together...just keep screwing the new ring on until it tightens.
Customer
Reviewed in the United Kingdom on November 12, 2017
Look nice!!
Recommended Products