Shopping Cart

Your cart is empty.

Your cart is empty.

5.9 Intake Elbow Tube Fits Dodge Ram 2500 3500 2003-2007 5.9L Cummins 3 inch

Free shipping on orders over $29.99

$53.80

$ 23 .99 $23.99

In Stock

About this item

  • Fits for Dodge Ram 2500 3500 03-07 5.9L Cummins
  • Package included: 1 Set of Intake Elbow with Silicon Hoses, and T-Bolt Clamps
  • Material: Made of high quality CNC machined billet aluminum and stainless steel, durable in use
  • Professional installation is highly recommended ( No instruction included )
  • Note: Please carefully check all the product information to ensure this is the right one you want before placing your order


Fitment:
for Dodge Ram 2500 3500 5.9L Cummins 2003 2004 2005 2006 2007
Package included:
1*Intake Elbow(red painted)
1*Silicone Boot
2*3" Clamps
Bolts/Nuts
Note:
Please contact us if there are any questiones about our products, your satisfaction would be our greatest motivation


Cameron
Reviewed in the United States on March 18, 2025
Fits 2003 cummins but doesnt line up properly, must shorten the intercooler pipe to get the boot to fit
Yavo
Reviewed in the United States on July 27, 2024
Se ajusta a la perfección en mi Ram 3500 2006.
R.M.
Reviewed in the United States on November 11, 2024
My only issue is the plugs weren’t tight. I should have checked. They were in place but probably only hand tight. Fortunately one of the ports was not a true port and that plug was not needed. I lock tighted all the plugs and got it sealed up. Seems to work.
MEZ
Reviewed in the United States on October 15, 2024
Lightweight aluminumFittings need a little Teflon or joint sealer, otherwise installed good and works greatAlso not a bad idea to use some hairspray on the inside of the silicone boot to help it seal so there are no boost leaks. Someone suggested that online and I did it.
James B.
Reviewed in the United States on April 24, 2024
Should help in performance and fuel mileage
Scottwayne Wootton
Reviewed in the United States on September 9, 2023
Things I needed to install this product.1. Needed 2 gaskets needed one below and above the intake heater $26.2. metric bolt M10 x 1.00 pitch you’ll have to cut it shorter so buy a nut as well. $43. use the old boot, not the one provided it’s too short.4. You’ll need to shorten the metric bolt and the bolt that holds the dipstick to the bracket.5. Remove dip stick from dipstick tube. I broke mine off cost me $15 to replace.6. Assemble the boot with the two clamps first do not tighten. Tighten four bolts to 18 ft lbs. stainless steel clamps. wasn’t easy but doable. the flange welding penetrated the tube and did not leave. A smooth interior. I cleaned it up best I could, but next time I would just buy a better product.I would’ve save money by buying the one that came with the two gaskets and hopefully a better welding job but all in all it’s installed and it runs.
srukke
Reviewed in the United States on July 21, 2022
I wouldn't buy. It won't fit what they say it does. It was way off for my 04. Couldn't line up the cold side intercooler tube to the end of the horn once it was bolted down.
Slickens
Reviewed in the United States on February 6, 2021
Used for direct replacement of the stock equipment, quality is good welds were great, bungs were sealed great, only downfall is there was no way to attach the dipstick tube to the top of the pipe, it made install very difficult because there’s nowhere to put the dipstick tube besides zip tie it down. Would suggest the manufacture to weld on the support for the dip stick tube, would make this product a full 5 stars, would also suggest the manufacture to add the gasket since we have to re use the original bolts, would make it 10 times easier to have it as a kit instead of purchasing a separate gasket. Hopefully they reach out to me concerning the extra bolt hole to attach the tube too I’d be willing to test fit the new product. Other than that great fit everything else lined up besides the clamps were too big to tighten down the boost tube that’s supplied with the pipe, re use your old clamps or just use the old boot and clamps. Don’t let any of this deter you from buying, the color and powder was great!! Packaging was great and it beats spending almost 200 dollars on one with a sticker.