Shopping Cart

Your cart is empty.

Your cart is empty.

4PCS Intake Manifold Tuning Valve Runner Arm Fit for 2011-2018 Chevrolet Sonic Cruze Chevy 1.8L Replace 55570283

Free shipping on orders over $29.99

$14.99

$ 7 .99 $7.99

In Stock


Fit for Chevrolet Sonic Cruze Chevy 1.8L Direct Replacement Specification: Bearings are Direct Replacement. Strict quality control standards to Buildand test. Look for compatibility list for fitment orjust ask us. Replace for 2011-2018 Chevy Chevrolet Cruze- Sonic 1.8L engine intake manifold Tuning Valve Runner Actuator linkage , Rod, Arm Fit: For 2011 -2018 Chevy Chevrolet Cruze - Sonic 1.8L engine For GM 1.8 Liter I4 Ecotec LUW / LWE Engine Features: 1.High Quality& High Performance 2.Easy install 3.Simple operation Package Include: 4x Tuning Valve Runner Arm


MacK Smith
Reviewed in the United States on August 28, 2024
Correct size and very close aftermarket repair arm. The upper ball socket does not correctly fit my 2015 sonic 1.8l configuration. It's way too loose, the doorman product (brass socket ball version) fit perfectly. Your configuration may work better, my vehicle @140k miles
Kyle
Reviewed in the United States on November 14, 2024
These don't even come close to fitting! The ball end is too big and the other end is as well. Don't waste your time with this trash!
Artur Zacarias
Reviewed in the United States on April 15, 2024
Works perfectly, the value is great and fits on 2012 chevy cruze.
Alex Armendariz
Reviewed in the United States on August 8, 2023
Not very easy to install
roger piercey
Reviewed in Canada on July 2, 2023
Fit perfect to vehicle
Frank Ten
Reviewed in the United States on May 29, 2023
Do not sand down the male ball end, it will not work. Do not attempted to push in the runner arm without removing the tuning motor unless you have super strong hands! What I had to do is take off the tuning motor (3 bolts) and lube up the male ball end of the runner arm with grease and it went in perfectly. You can use Vaseline if you don't have grease. Then install the tuning motor with the arm connected to it. Finally connect the female end. Should take about 30 minutes. This took off my P2076 EVEN THOUGH my 2014 Cruz still had a runner arm in place. I guess the ball end was wearing out and if it's off by the slightest degree, it will throw the code. It has been 2 weeks and the code has not come back after I cleared it with an OBD II.
Mike
Reviewed in Canada on November 7, 2023
You just saved our client 1700 for parts and labor as this rod is not available purchase separately from the gm dealership. Thank you!!!
Dean's Performance
Reviewed in the United States on November 29, 2023
quality fitment
Xamy Xorgan
Reviewed in the United States on October 6, 2023
This was difficult to get in place. But it did fit perfectly and is working beautifully. I ruined one trying to figure out how to get them on, and one is on my car and has been for several months with no problems. The other two I keep in my glove compartment in case I need them. If you have a 2013 Chevy cruze, this will fit if you can get it on. I won't lie and say it's easy, but you can do it.
Stee
Reviewed in Canada on October 25, 2023
Il fait parfaitement et en plus vous en avec 3 de surplus.
Elric C Wright
Reviewed in the United States on April 23, 2023
Seemed to be well built, but did not fit my daughter's 2013 Chevy Cruze