Shopping Cart

Your cart is empty.

Your cart is empty.

4 x 47mm W1 Heavy Duty Spring Band Clip Radiator Pipe Air Oil Fuel DIN 3021

Free shipping on orders over $29.99

$21.14

$ 8 .99 $8.99

In Stock

1.Size:Ø 17mm


About this item

  • Heavy Duty Spring Band Clamp.
  • Pack of 4.
  • For use with heavy duty hose applications.
  • Measurement is the Ø diameter of the clip.
  • Manufactured according to DIN 3021.


Heavy Duty Spring Band Clamps
Pack of 4

For use with heavy duty hose applications.
Spring loaded high carbon steel strip with zinc plated finish.
Manufactured according to DIN 3021.
Measurement is the Ø diameter of the clip.
Designed to maintain a constant seal around the hose with a fluctuation in pressure.
For use with automotive, agriculture, aviation, material handling, marine, plant & construction.
This clamp is recommended for applications where temperature can vary from -40ºC to +120ºC.
It's design means that it can maintain the same radial force despite constant changes in temperature.
One of the great attributes of this clamp is it's easy to mount and is reusable.
They have a wide application in manufacturing industries including:
Agriculture
Mining & construction
Military
Boat builders & aircraft
Gas & chemical industries
Medical equipment
Welding equipment
Commercial vehicle manufacturers
Heating & ventilation
Compressed air systems
Caravan manufacturers
Building & plumbing
Plant spray equipment
Vending machines


LC
Reviewed in the United States on October 14, 2023
Difficult to find clamps fit and functioned perfectly. Would purchase again if needed.
kurt
Reviewed in the United States on April 30, 2023
I upgraded my wrangler with silicone raidiator hoses new radiator and water pump I used the hose clamps that Mishimoto provided So I was suprised to find a puddle of antifreeze under the jeep in less than a year those worm gear hose clamps had become loose So there is a real reason why the factory installs spring clamps they will stay tight through cold and heat because they have spring action not a worm screw So it`s thesetype of hose clamps from now on
Wendy
Reviewed in the United States on February 13, 2022
The "nominal size" is the OUTSIDE diameter of the clamp (unexpanded), not the inside (as shown in the diagram), nor the best size (mid way between min and max clamp ID) for a particular hose OD. For larger hoses this does not make much difference because your hose OD and clamp OD is still within its operating range. HOWEVER, for smaller diameters like my 19mm this is a deal breaker (see photos).I ordered these 19mm clamps for 3/4" hose (O.D.) on my current engine build; waited about a MONTH for slow shipping from UK; then found that there was NO way to get these clamps on my hose. The ID of the 19mm clamps was about 15.6mm and even full "open" wouldn't fit. So bottom line was; I delayed my engine build for a month waiting for these clamps (difficult to find), then found them to be about 3mm too small because the diagram of "nominal" diameter and chart of (min/max) was misrepresented.So four things to consider: one - the "nominal" diameter (at least for my order of 19mm) is OD of clamp not your hose OD (like it should be); two - these clamps are produced and shipped from the UK and standard shipping will take close to a month; three - these clamps are expensive (my four little clamps were $14); four - these (as advertised) are Heavy Duty, which for larger diameter and higher pressure hoses is great but maybe just a bit overkill for things like 1/2" vacuum lines, lol. For instance a standard 50mm (2") clamp has an opening force of 410 N which is almost 100 lbf !!!
Kyle
Reviewed in the United States on November 11, 2022
I followed the advice of another rating that the dimension in the chart is the outside diameter. This was not even the case for mine. I ordered the 4 x 40mm and the overall outside diameter of the clamps I got was 36.85mm.I gave two stars because the item shipped faster than expected and it does seem like it is good quality. I just don't think I can use this smaller size.
k.m.s.
Reviewed in the United States on April 30, 2022
Replaced the worm drive clamps on oil return lines that were seeping. The screws were loosening and because the hose was only 1/2”, the clamp wouldn’t make a tight seal totally around the hose. These work by compression and seal the hose TOTALLY.
Emmitt T. Kelly
Reviewed in the United States on August 14, 2021
HARD TO FIND THESE AT PARTS STORE..VERY IMPORTANT IF YOU HAVE A RADIATOR WITH PLASTIC TANKS
Micah J Villarreal
Reviewed in the United States on June 21, 2021
I ordered these hose clamps to replace some stainless worm screw clamps that were cutting I to my radiator hoses. They were 47mm and my hoses were 50mm. They were tight I was able to get them on by squeezing them with a pair of channel locks and they compressed the hose on the fittings very well. I liked that they came in a small pack of 4 and not a giant pack of 25. They have good spring action and I am happy with them. They seem just as good as OEM quality.
Jen
Reviewed in the United States on September 25, 2017
I love these constant force clamps, as they grow and shrink with temperature cycles and help your plastic cooling system parts and rubber hoses live longer. Plus, with the right tool, they are super fast to install and remove in the pits. Thanks to this seller for having all the odd sizes available! Beats going to the dealer.
Recommended Products

$10.93

$ 4 .99 $4.99

4.6
Select Option