Your cart is empty.
Your cart is empty.Product Description
Packaging includes
1 x vfd and spindle
- 1 X 220v input 2.2kw vfd （comes with a manual）
- 1 X water Cooled 220V-2.2KW 4bearings Φ80mm 400hz spindle (come with a 6mm collet)
1 x 80mm motor clamp
- Adopt high quality aluminum,the surface is oxidized polished, very smooth,safe to use.
- the accuracy is much higher , and it is hard to deform
1 x 220v water pump
- AC:220v-120V/50HZ 75W Hmax:3.2 QmaxFlow Rate:3200L/H Waterproof Grade:IPX8
- Easy to detach and clean
- Designed with a adjusting knob, allowing to adjust the water flow rate.
- Rubber suction cups can be a good fit in the glass surface, to help keep it stability.
1 x 5m hose
5 meter length hose, outer diameter 8mm, inner diameter 6mm
VFD specifications
- power:2.2KW
- horsepower:3HP
- input voltage: 1 or 3 phase 220V(±5%),
- output voltage:220V 3 phase
- input Frequency: 47-63Hz
- output frequency:0-50/60hz 0-400hz
- Rated current:10A (Represents the maximum current the VFD can withstand)
Spindle specifications
- Bearing: 7005 (2pcs)and 7002(2pc) bearings
- Voltage and rated current: AC 220V, 10A
- Operating speed:8000rpm-24000rpm
- Radial runout:≤0.025mm clamping mandrel vibrates at 30mm to nut
- Frequencies: 400Hz
- Size:80*238 (mm)
- Collet: ER20 collet, 6mm is standard
- Nut model: ER20-A(B)
Establish a connection
- The single-phase input wire is connected to the R and T terminals, and the motor output wire is connected to the UVW terminal of the VFD.
- basic parameters for 400hz spindle：pd013=8，pd005=400,pd004=400 pd003=400 pd072=400，pd144=3000, pd002=1 pd070=1，(All VFD parameters are set before delivery,so you can connect and drive directly after you receive the kit)
VFD function introduction
Diverse terminals, more functions for you to choose.
- supports external potentiometer control (connect the "FOR" and "DCM" terminals,than set PD001=1)
- supports mcah3 function and RS-485 communication
- (For more information, you can contact the seller, we will send you a video of the basic functions of VFD)
Key Function
- UP: Progressively increase data or function codes.
- DOWN: Progressively decrease data or function codes.
- SET: Enter menus step-by-step, save setting parameters.
- PRGM: Exit current(or present) state, switch among each states, mainly used to switch monitoring state, exit to previous menu.
- FWD/REV: 1, Press momentary button to start,release to stop; 2 Switch the rotation direction
- SHIFT: Switch monitoring parameters at monitoring state, at secondary menu, move data box to process editing position.
- Kindly Note: If you want to show RPM in the display,please press 'SHIFT' key
Advanced motherboard features
- PID control; advanced calculus PID closed-loop arithmetic, quick responding speed and high suitability
- Easy PLC function can realize 16 legs of speed and inverter control function
- RS485 communication port, adopting standard international MODBUS main circuit control
- With extremely strong anti-jamming capability
- Low output ratting torque0.5HZ-150%, low speed running ability
- Carrier adjustable by 16KHZ, completely soundless working environment
- Broad voltage working area, normal running in 304V-456V
- Auto voltage regulation (AVR) technique, for ensuring the inverter load capability
- With perfect error protection and short circuit starting protection capability
Spindle introduction
4 high precision bearings
With 4 high-precision bearings, high precision and strong torque are guaranteed
Aviation connector
Power interface: YX20 water proof aviation plug marked with number 1, 2, 3, 4. Number 1, 2 and 3 inter-faces are connected with inverter power U, V, W respectively. Number 4 is connected with earth wire
80mm spindle clamp
- High accuracy
- Powerful clamping effect
- Excellent elasticity
Adam
Reviewed in the United States on September 6, 2024
I'm happy with this spindle. It's quite and has plenty of power for what I need
Andy Mosqueda
Reviewed in the United States on July 24, 2024
Awesome unit works flawlessly and is very quiet.Easy to set up and plenty of smart people on Utube to help you understand the settings.Thank you
Shambles75
Reviewed in the United States on July 19, 2024
Got this kit a few months ago - took a minute to wire it up - but it was fairly easy. The instructions provided are in broken/improper english but nothing youtube cant fix ;-) Got everything wired in and hooked up - first carve was a 13 hour carve and my GFCI kept popping - come to find out VFDs are synonymous with tripping GFCI outlets. I tried a less sensitive GFCI and got no love. Swapped to a regular outlet and we were back in the race. Ran flawlessly - BE SURE TO RUN THORUGH ALL THE VFD SETTINGS. The ones supposedly preset are incorrect so I'd recommend you verify each one that applies to your setup. Worth the money IMO. Side note: the vendor should remove the 65mm mount and replace that with a water tight 5 gallon container for the pump.
Paintball K.
Reviewed in the United States on May 1, 2024
Well packaged. Decent install instructions.Bought better quality water lines, a CW3000 chiller and a double shielded VFD to spindle cable. Run about 60 hrs for far including an 18 hr continuous job. Never got over 7 degrees about room temp. Works great and so much quieter than a spindle.
Liendeni
Reviewed in the United States on August 8, 2023
First, some negatives as others have mentioned...the water pump is worthless. It has a 110v cord on a 220v pump. Not the end of the world but annoying. This is just pure laziness. 1) They should have enough common sense to not advertise it with a water pump to US customers if they know 100% you are not getting a water pump. 2) No wrenches as others have stated. 3) Next to zero accurate documentation.There is a comment to not do the wiring unless you are a electrician. That is silly.Here is what I did.1) I bought this power cord. " 20FT NEMA 6-15P/6-15R Power Extension Cord for 220/240V Air-Condition,...." ... here on amazon...2) I cut the end not going to the wall off3) I bought the blue colored ring connectors from HDepot4) I hooked black and white to any two of the power connectors (can't recall the letters UVW? easy to look up). I hooked the ground to the only ground on the VFD.5) I purchased the wiring that went between the VFD and Spindle ready to go...premade from corvetteguy50 - easy to find for $230 shipping. In his video he will tell you how to hook up the wires...super simple. I put both grounds on the only ground screen on the VFD. Green from the 220 cord you purchased here on Amazon from above and one from green ring connector coming off the ground from wire purchased from corvetteguy.6) I cut the original orange water pump line in half.7) I put the original water pump screen in adapter onto the new water pump (its the right size..you will need this)8) Connected the water lines (one going to Spindle from new pump and one going from spindle into water bucket).9) I tested to make sure the water pump was flowing with no leaks.10) I programmed the VFD as shown on most videos. I only programmed 2 codes I do believe - PD005 and PD004.11). I turned it on.12) Tested a cut...completely tore up the wood.13) Spend 7 hours in the garage trying to figure out what was going on...went to bed unresolved.14) Woke up and realized the spindle was sent programmed to spin the wrong direction.15) Hit the REV button on the VFD...spindle spins correctly now and everything works great.I hope this helped someone. Figuring out how to do this...took much more time than actually doing anything. Was way easier than I thought it would be and I'm no electrician. Be careful and the above is not electrical advise...just telling you how I got this mystery thing to run. And I bought this water pump from Amazon ..."VIVOSUN 800GPH Submersible Pump(3000L/H, 24W)" - Keep the hose to pump adapter from the old pump...you will need it. And that's it. I was out the door for about $650 or so but way better than the $3500 my CNC company wanted for a 1.7KW HSD Spindle and VFD. Besides, if one part goes bad on this unit....you now know how to fix it.
Alex
Reviewed in the United States on July 1, 2023
The bad first. The water pump didn't work but it's not why would buy this. Just plan on buying a good quality pond pump. Otherwise it has been great. I've done several 24 hour plus cuts without a hiccup. The VFD is tied into my CNC controller so the G code commands it to start, sets the speed, and to turn off once it's done. After 24 hours the spindle is warm to the touch but not hot. It has lots of power. I use a CMT 2 3/8" surfacing bit set to 8000 rpm. It handles it without an issue. I've even used a 3" half round bit. ust add ferrite beads on the power cable for the spindle.
Heike O
Reviewed in the United States on March 9, 2023
I bought the kit, spindle with correct VFD, beause it said it would be 'ready to go' as VFD was set by factory. Well, it worked for a while. During light duty minimal flattening of the spoil board it stopped w/o warning and w/o any workload, it showed EoCA. I restarted it and after another hour the same happened (flattening w/ 1" planer I had a new spindle for a while and performance was mediocre. Today however my VFD just sparked and went up in flames. I realized this immediately or else my shop could have burned down. I am reducing to one star.
Felix
Reviewed in Canada on June 16, 2022
Where should I start...EMI (electromagnetic interference) was a big issue since the beginning. After months of investigation a ton of $ in anti-EMI device, it's less bad, but it still stops communication between the controller and the CNC...After one year of non-intensive use, the spindle started to do free games... I even had to reduce my dept of cut for my spindle to handle super conservative parameters...The seller was not helpful, his advice made no sense, communications were poor, and he even wanted me to send my email to a non-secured weird email… Since the warranty was only 6 months, and my purchase was done last year, he never refunded. He offered a small discount on a new one…. Never replied after my last communication…
Ryanccc
Reviewed in Canada on December 20, 2022
Works excellent, good quality VFD and spindle
Don
Reviewed in Canada on December 17, 2019
Great price
X Caper
Reviewed in Canada on April 8, 2019
Exactly as described, arrived quick, and works perfectly. Using on a home made CNC.
Recommended Products