Your cart is empty.
Your cart is empty.Product Description
Easy to Cut
- Polycarbonate plastic is easy to cut and comes with EasyRuler film to make following lines easier.
- Can be cut with saws such as a hack saw, circular saw, table saw, or jigsaw if equipped with a suitable blade. You can also use tin snips for 1/32" and 1/16" sheets, or CNC machines
Drill with Ease
- Polycarbonate sheets are easy to drill. Use the crossing lines to space out holes with ease in these clear plastic sheets or tinted plastic sheets.
- Unlike plexiglass or acrylic, polycarb panels can be drilled without cracking or shattering.
Bend or Thermoform
- Polycarbonate is easy to bend with heat. Thin plastic sheets can be cold bent too.
- Polycarbonate can be formed into different shapes with just a typical hand held heat gun.
- These PC sheets are often used for vacuum forming or thermoforming too.
Make Circles with Ease
- EasyRuler film makes shapes easy to follow and keeps the plastic surface clean until you are ready to peel.
- Mark your work the protective film, make the cuts and peel to reveal a protected and pristine surface.
Darrell
Reviewed in the United States on March 16, 2025
Worked great for making the panels for the 1/12 buggy.
Film lover
Reviewed in the United States on July 23, 2024
Unlike thicker sheets, this was thin enough that instead of sending it flat, they sent it rolled up in a box. Not a tight roll, maybe a 6-inch radius (I didn't measure), but enough that I was not able to get this to be flat again, after a week of trying. That made it useless for my purposes so I sent it back and got the 1/16" thickness instead.Of course, if you want something that could bend into a cylinder, this might be just what you want.
Geoffrey Lyle
Reviewed in the United States on June 3, 2024
Product is great quality however came rolled up and its very difficult to get flat now which is needed for the application. If you don't need it flat then this is a great product for you.
Rennie G. Gibson
Reviewed in the United States on May 4, 2024
Just know that you will receive this rolled up. Very hard to get it back flat.
Nathan Bagwell
Reviewed in the United States on May 15, 2024
The media could not be loaded.
Matthew D'Arcy
Reviewed in the United States on November 17, 2024
Never leave reviews but saw a lot of people complaining about how it’s shipped in a tube and it’s nearly impossible to get the warp out to lay flat. I took the racks out of my oven and set it to like 200. Once preheated, I put it on a cold baking sheet and slid it in there “standing up”. Left her in there for like 4 or 5 minutes and it actually already started opening up on its own and started touching the sides of the oven. So I pulled it out and put it on a table with lots of books on it for about 10 minutes and it took it! It lays perfectly flat now after a total of like 15 minutes. Not bad.
Isaiah Salas
Reviewed in the United States on March 5, 2023
If you absolutely need a flat surface as I did, I cannot recommend this product. I don't know if this was just a me problem or if this is how they ship it to everyone, but mine came rolled up as if it were a poster. If you know anything about thin plastic, then you know that it loves to retain it's shape especially when it's warm. It showed up basically unusable and any attempt to flatten it out resulted in plastic warping. Some said to place it between two sheets of glass and let it sit out in the sun, but since it's been a high of 20 degrees Fahrenheit, I doubt that would do much here in Colorado.
Ron or Chris Embry
Reviewed in the United States on September 6, 2022
I was able to use two sided sponge tape to attach this to my garage wall where my car door opens. Our garage is right so my car door opens against the dry wall damaging it. I repaired the drywall and put the plexiglass there and it absorbs the door being pressed against it and does not mar or crack. It’s perfect. Exactly what I wanted. The songe tape gives it a bit of shock absorbency so it’s not resting directly on the drywall.
Recommended Products