Your cart is empty.
Your cart is empty.Product Description
4-Ports PCIE to SATA III 6Gbps Expansion Card for Desktop PCs and Servers
LTERIVER PCE-G3S4 is a PCI Express Gen 3 to SATA III (Serial ATA) 6Gbps controller expansion card. It will covert PCIE 3.0 X1 signal to 4-Ports SATA III on desktop PCs, Working Stations, MAC Pros and NAS. The PCIE 3.0 X1 interface will provide 8Gbps total bandwidth for 4X SATA III ports. Allow users add 4X max SATA HDD/SSD on their system for AHCI Boot or Storage Expansions. This PCIE SATA III card will support Plug and Play on Windows OS, Linux kernels, and MAC OS systems, now no need to install driver anymore for PCIE SATA expansion cards.
WARNING:
1.This PCE-G3S4 PCIE SATA card no need to install driver, if PCs or Servers cannot find the added-on HDD/SSD and this device, then double check if the mother board PCIE slot is active and open. Some brand mother board may have defined PCIE function when it produced. User better call mother board manufacture locate the problem.
2.PCE-G3S4 was set on AHCI mode. If users using the classical IDE mode, user’s PC will report BSD error. If users do not know which mode is running on PCs, follow steps as below: Windows Device Manage-IDE ATA/ATAPI Controllers- Will see “XXXX SATA AHCI controllers” or “XXX IDE controllers”.
3. PCE-G3S4 is designed on PCIE X1 interface, will works on PCIE X1, X2, X4, X8, X16 slot. Normal users better check if it has empty PCIE slot before purchase.
4.If user add the new or recovered HDD/SSD on the system, users must add this disk on system by Windows reminder in Windows Device Manager-Storage-Disk Management.
Technical Specifications:
8Gbps Bus Banwidth,SATA III 6Gbps
- Based on PCIE 3.0 X1 Signal, Provide 8Gbps Total Banwidth.
- Light up 4X AHCI or Storage SATA III 6Gbps SSD/HDD on Systems.
Heat Sink on ASMedia ASM1164
- Select the ASMedia ASM1164 PCIE 3.0 to SATA III Host Controller.
- The Added-on Heat-Sink will Protect the Major Chip ASM1164 from Overheat.
- Will Works on AMD, ARM and INTEL Hardware Platform.
Standard and Slim Size PCs
- The Full Size Bracket Mounted on this PCIE SATA Card,will Works on Standard Size PCs.
- The Low Profile Bracket in the Package will Works on Slim Size PCs.
Windows OS,MAC OS X,Linux Kernel
- Plug and Play on Windows XP, 7, 8.X, 10, 11 (32/64bit) and Windows Server 2003, 2003R2, 2008, 2008R2, 2012, 2012R2, 2019, 2022 (32/64bit).
- Driver Free on MAC OS X and Linux Kernel Systems.
PCI Express 3.0 X1 Interface
- Based on PCIE 3.0 X1 Interface, will Works on Motherboard PCIE X1, X2, X4, X8, X16 Slot. Users Must Check If PCs Have Empty PCIE Slot.
2.5in SSDs and 2.5/3.5in HDDs
- Seamless Connect to SATA III/II/I SSDs and HDDs.
- Light up 4X Max 2.5in SSD or 2.5/3.5in HDD in System.
Product Description:
LTERIVER PCE-G3S4 is a PCI Express Gen 3 to SATA III (Serial ATA) 6Gbps controller. It will covert PCIE 3.0 X1 signal to 4-Ports SATA III on desktop PCs, Working Stations, MAC Pros and NAS. The PCIE 3.0 X1 interface will provide 8Gbps total bandwidth for 4X SATA III ports. Allow users add 4X max SATA HDD/SSD on their system for AHCI Boot or Storage Expansions. This PCIE SATA III card will support Plug and Play on Windows OS, Linux kernels, and MAC OS systems, now no need to install driver anymore for PCIE SATA III expansion cards.
WARNING:
1.This PCE-G3S4 PCIE SATA card no need to install driver, if PCs or Servers cannot find the added-on HDD/SSD and this device, then double check if the mother board PCIE slot is active and open. Some brand mother board may have defined PCIE function when it produced. User better call mother board manufacture locate the problem.
2.PCE-G3S4 was set on AHCI boot up mode. If users using the classical IDE mode, user’s PC will report BSD error. If users do not know which mode is running on PCs, follow steps as below: Windows Device Manage-IDE ATA/ATAPI Controllers- Will see “XXXX SATA AHCI controllers” or “XXX IDE controllers”.
3. PCE-G3S4 is designed on PCIE X1 interface, will works on PCIE X1, X2, X4, X8, X16 slot. Normal users better check if it has empty PCIE slot before purchase.
4.If user add the new or recovered HDD/SSD on the system, users must add this disk on system by Windows reminder in Windows Device Manager-Storage-Disk Management.
Package: 1X PCE-G3S4, 1X User Manual, 1X Low Profile Bracket, 1X Mount Screw, 4X SATA Cable
Me
Reviewed in the United States on February 23, 2025
Had a SATA port on my motherboard quit working. Had a DVD drive that my computer quit recognizing. I added this SATA card, connected the drive to it, and now it works like it is supposed to.
E Mad
Reviewed in the United States on July 27, 2023
Installed connected my raid and blue ray player pwr up the system and here it goes, already recognized by the system. GREAT STUFF, HIGHLY RECOMMENDED.
clintkeep
Reviewed in the United States on September 16, 2022
These tiny cards failing to work is almost unheard of. They're very basic. Installing it was simple modifying it was a snap However I don't think these translate well for things that need an extra power source such as a hard drive. But there is no room on this card for much more. I used this in a Dell Optiplex which is why I have no space to work with as it is. This card is a great and helpful addition when I needed to hook up my 2 gig heavy blocky and dying ATA drives.
Customer
Reviewed in the United States on September 13, 2022
PCIE 4 port SATA extender, with cables.This has enabled me to replace the one 3.5” HDD with 2 smaller , faster , quieter, lower power SSD drives inside the case of my Dell XPS 8930 which has limited space , power and connections.The card is very small and this is great because it leaves more room to route the SATA cables.I already had spare cables but was really pleased that this card came with 4 straight ended SATA cables because you need to use straight cables to fit them in to the connector block on the card. I also needed to use straight ended connectors for my SSDs because 2 of them were stacked together in one 3.5” bay.The SATA cables are the locking type , which is good, although I found when 2 were stacked on top of each other the locking mechanism was depressed because the top cable sits so close to the bottom one, so no different to a normal cable in this scenario. I’d still rather have locking cables for all the other connections.Note: to add the extra drives I also needed additional Power connections and a 2.5 to 3.5 mounting bracket which do not come with this card. I used a power splitter cable which split one power connector in to two.Price seems right and these come with SATA cablesPROsSmall card allows room for cablesStraight end connectors SATA cables suppliedPlug and play (windows 11 system)Easy upgrade.CONSPower splitter cable would have been nice
JP
Reviewed in the United States on August 7, 2022
This review is of the LTERIVER PCIe 3.0 X1 to 4 Port Serial SATA 3 host controller. The package came with the standard bracket, a proper low profile bracket, retention screw, and four locking SATA cables. I tested this in a HP Elitedesk 800 G2, and booting into the BIOS I could see the drive attached to this card and set one as the boot device. I could also boot from it, which is great. As such no drivers are needed to be installed in Windows 10, though I didn’t try doing a fresh install to ensure that it worked there.PROS:Proper low profile bracket card!Four locking SATA cables (due to the locks, the upper cables should be installed first)Status/Access LED for each SATA channel on the card to aid in troubleshootingNo additional power cables needed, simply plugged into PCIe X1 slot to workWorks with Windows 10 and Debian Linux (kernel v5.14) (systems tested)CONS:None so farOverall, a nice card that I would recommend for those who need extra SATA hookups.
Zastavan
Reviewed in the United States on August 31, 2022
it works fine with no issues so far. Plenty of people recommended this type of device which is why I went with it and it works so far.
J F Seattle
Reviewed in the United States on July 25, 2022
I was looking for a SATA controller card that I could add to my system to service a couple optical drives that I'm just not ready to let go of. For a new motherboard with 6 SATA ports, I was frustrated to see two of them were disabled by using a certain m.2 slot and I already have 3 of 4 of the remaining slots filled with SATA SSDs. I picked up this 4 port LTERiver PCIE 1x card to gain 4 SATA ports, of which two I am planning to use for BR and DVDR-W drives immediately. This kit includes a low profile bracket as well as a pre-installed full-profile bracket, 4 locking 15" SATA 3.0 cables, and a PCIE 3.0 x1 card that's small and won't block airflow. The card has a ASM1064 controller chip with a decent sized heatsink on it (while good for longevity in general, plenty of motherboards come with this controller chip and no heatsink attached to it), 4 blue drive access LEDs soldered onto the card (there is no header for a case HD activity LED, but those have gone out of style for a while now), and the female SATA ports are designed with the use of lockable SATA cables in mind (sometimes it's nice to not be able to lightly bump a SATA cable and cause it to unplug).I had no issues powering down my system, installing the card, and then putting it to use with my drives. My biggest concern is that the blue status LEDs are on the side of the card that's not visible in most ATX cases, including my own.The price of this 4 port SATA card seems comparable to other non-RAID controller cards available on Amazon and this kit includes some SATA cables to boot.
Paul W
Reviewed in the United States on April 2, 2022
Plugged it in and detected right away by windows 11. No issues so far.
Recommended Products
$225.00
$ 91 .99 $91.99