Your cart is empty.
Your cart is empty.Product Description
MNA tools have all of the standard woodworking carbide router bits you need to complete your woodwork projects.
MNA Industrial grade bit specialist for any application. Use these bits for precise work on any wood material and for any task of routing job that keep after working surface in a smooth, cut burn free. Great for hardwood, softwood, plywood, composites and laminates on hand-held or table-mounted routers. Two flute bits provide faster cutting and three flutes yield a superior finish.
American Standard
Made for American use
Precise Dimension
Provide the shape you want
Anti-Kickback Design
Limited the 'chip-thickness' of the material being cut, offer some degree oof safety to user
Protective Coating
Improve the body resistance and minimize the friction
Minimum Vibration
Provide flawless milling cut
Hi-Density C3 Carbide
Carbide tips provide superior wear resistance and long life
STEVEN BAMMANN
Reviewed in the United States on May 30, 2024
Would have liked 1/4” longer shaft
i.buy.things
Reviewed in the United States on October 7, 2024
The bit is not balanced at all and at even lower speeds rattles my router. Sure it runs but it can't be good for the router at higher speeds and feels unsafe.Feels like quality of a $10 bit. Returning this.
RoR
Reviewed in the United States on August 9, 2023
Worked perfectly. Anything less is not acceptable.
Michael Franklin
Reviewed in the United States on June 9, 2023
If you work with routers, you are well aware of the unbelievable range in quality when it comes to bits. I would say better than 50% of the ones available on the market are sub-par. Finding one that isn't is sometimes a challenge.This MNA 1/2" (Dia.) Double Flute Straight Bit with 1/2" Shank is definitely a quality bit. I work with Hardwoods most of the time, which can dull a cheap bit with one use. I put this to use about 5 months ago and again this past week. I have probably made 40+ cuts with it. As of Sunday's use, it was still as sharp and true as it was 5 months ago.The edge that it leaves is almost smooth enough to not have to sand on some pieces and I have not tried to use it for joints. I am going to try rabbets with the shelf unit that I am putting in our RV.This is a High Quality Bit that is holding up just fine versus Oak, Black Walnut, Maple and Poplar. I would recommend this for any serious woodworker. Good stuff.Quality Bit
Amy Biermann
Reviewed in the United States on March 17, 2023
Bit shattered after three cuts. Routers spin way to fast for this kind of junk. Potential for injury is real. Needed the oddball size for one job to save time. Wasted money and not saving any time. Lesson to learn? Yeah, for high speed bits, pay for quality.
DJ
Reviewed in the United States on October 14, 2023
Nice sturdy bit and good price. Cut great
Larry Burchfield
Reviewed in the United States on December 24, 2022
5/8 deep in 14 12' 2x4's. bit did great for the price
Espoir
Reviewed in the United States on December 16, 2022
This review is for the MNA 1/2" shank, 3/4" diameter flush trimming router bit with both top and bottom bearings. Cutting length is advertised as 1-5/8" and measures a little longer at 1.66".This is a quality router bit with bearings on both ends of the cutter to allow flush trimming of laminates or trimming to pattern templates placed on top of or under the workpiece. Both bearings are 3/4" O.D. The end bearing is about .280" deep with a small inner diameter for the socket head screw. The bearing on the shank is narrower at about .156" wide and necessarily has a 1/2" I.D. to fit over the shank. A collar with a set screw holds this bearing in place.The carbide is about 0.84" thick. The bit is well balanced and since it's new it cuts like butter. There was a small nick in one of the carbide edges, but the other was perfect and no bead line was present on cuts because of it. Not enough to down rate it by a full star in my opinion.Looks like a pretty good quality product, although I might compare with other name brand equivalents for pricing. 4 1/2 stars that we'll round up to 5 in this case.
MR Jick
Reviewed in Canada on November 22, 2022
Very sharp nice bit, it did hope alot on my yearend project! Yes Lego table, the bit could save the time for sanding. i suggesting slow feeding and not too deep because i did burn a bit at the end for the first run. it turn out a experience to adjust the speed and router depth.As you see the package is expected simple but the bit are extermly nice.i will try this MNA brand for the large set soon, Thanks for Bob for help on the plan
Recommended Products
$392.88
$ 99 .00 $99.00