Your cart is empty.
Your cart is empty.Franklyn Miller
Reviewed in the United States on February 23, 2025
Fantastic!!! It fits well and stays sharp. It cuts tiles, thin metal, and plastic without any issues. I would buy this product again and recommend it to others.
Gerald
Reviewed in the United States on January 25, 2025
This has been one of my best purchases. Cuts right through what my abrasive disk would not.
Gabriel Garcia Rojas F
Reviewed in Mexico on September 11, 2024
No vienen instrucciones de como montarlo al dremel
Bernie
Reviewed in the United States on May 8, 2024
Good price and quality compared to name brand
Kevan
Reviewed in Canada on March 5, 2024
I like this product it's very sturdy and durability is good Cuts nicely and it's locked a long time and still work shoukdnget a lot more cuts out of it
Felipe Arias
Reviewed in Mexico on March 1, 2024
Me gusto el disco, corte PTR de 2mm y lo corto mas o menos a la misma velocidad que el disco de corte normal, si, hace un poco mas de ruido, tambien se borro muy rapido lo impreso en el disco, pero es esperado, sin embargo lo impreso sobre el borde diamantado no se borro, eso parece indicar que la dureza del borde diamantado es la correcta.Hasta ahora no le veo problemas y me parece una buena compra, tengo que probar con mas cortes, pero en los que he hecho, se ve como una muy biena compra, lo recomiendo.
luvtotrade
Reviewed in the United States on November 30, 2024
Cuts the 1/8" metal easily as expected
THT
Reviewed in the United States on October 13, 2024
The size of shank is 10.1 mm, not 3/8 inch. Intentionally wrong labeling because 3/8 inch is 9.525 mm and smaller than 10.1 mm. The 0.56 mm difference can cause misbalance and strong vibrations with 3/8 shank. It can ruin the tool and easily kill somebody if used at speeds of 21000 rpm and 3/8 inch shank.
Rolidnot
Reviewed in the United States on June 5, 2023
My 30+ year old galvanized chimney chase cap was rusting out. I had it replaced with a stainless steel cap. The chimney contractor told me disposal of the old cap was my responsibility.The town where I live wanted me to make a special appointment to pick up the intact chimney chase cap and pay a $25 pick up fee so I did some research.The town where I live says it’s OK to put anything non-toxic that fits in their trash bin.I used this diamond wheel to chop up the galvanized metal cap so it would fit in my trash bin. Once I got the wheel started, it cut the 16 gauge galvanized sheet steel almost as fast as I could move the angle grinder.It took me 15 minutes to cut the old cap into pieces. This Diamond wheel is far superior to the vitrified cutoff wheels that are a mess and degrade quickly. The rapidly decreasing diameter of the vitrified wheels also make them cut slower.So I played by the town and waste law rules, didn’t violate any environmental laws and got rid of the cap thanks to this Diamond cutoff wheel. As you can see, I made it fit in the trash can.Hope that helps!
Luis F.
Reviewed in Mexico on June 28, 2023
Corta el metal como mantequilla aunque hace mucho más ruido que un disco regular, nada que no se resuelva con unos tapones de oídos!! Un poco elevado de precio pero excelente producto!!
John Lee
Reviewed in Australia on January 8, 2023
Less sparks and just goes on and on
Hotroddin1971
Reviewed in the United States on December 15, 2022
First it cuts clean I don't get filthy with the dust and debris like with the normal cutting discs. Second so far it has cut every type of steel I've tried it on. Third it doesn't break into little pieces throwing shrapnel at me which often hurt like hell. So far the only downside is that it cuts quite a bit slower than the composite discs. if it lasts a decent amount of cuts I'll definitely be buying another. haven't had and used it long enough to know durability and longevity I'll update later as I use this near every day on the clock. So far I'm very happy and impressed with it.Update #1 Jan 26 2023 it still works like it did when new and I'm probably at around 350+ cuts, very happy with this!!
Gerard K.
Reviewed in the United States on August 23, 2021
Using it, I am, as recommended (letting it cool off per schedule) is working well for me. From hot rolled metal to rebar to chrome vanadium I have had no problem in the way it handles cutting the metal I have used it to cut. The only issues: a) fitting it over the spindle; it came to me not as a slip fit but a press fit. I found this and still do find this aggravating for the extra delicate installation that is needed to fit it over and onto the spindle; b) once the label material wears off the disc is too thin to be held by the flange nut to keep it from spinning. I used some shim material to make a washer but at the price I paid this should not be happening.
Recommended Products