Shopping Cart

Your cart is empty.

Your cart is empty.

Enoin 1 Pack 12x16 Inches Orange Translucent Acrylic/Plexiglass Sheet 0.118'' 1/8 Thick, Plastic Sheet Colored Board Panel for Glass, DIY, Painting, Art Craft

Free shipping on orders over $29.99

$14.99

$ 7 .99 $7.99

In Stock

About this item

  • 【Note】The color will be different through the different brightness.
  • 【Color】Translucent: Red, Orange, Green, Blue, Purple, Pink; Non-Tranparent: Black, Red, Orange, Yellow, Green, Blue, Pink; 【Dimension】Thickness: 0.118'' (1/8'') Size: 12 x 16 inches
  • 【Fully Protect】Enoin always focuses on details. We take your safety and the damages of sheets into consideration. Our acrylic panels are well equipped with four protective cases on each corners & protective films on both sides. Not only to protect the acrylic sheet from the damages in transit, but also protect you from the scratch of sharp edges.
  • 【Smooth Edges】Enoin's acrylic sheets have precision cut and accurate producing on each sheet. There are no chips, no burns, no warps left on edges that makes each customer easy to DIY. Our acrylic plexiglass sheets is pure as glass, but harder and tougher than glass.
  • 【Wide Applications】Acrylic sheets can be used as table signs, photo frame glass replacement, cake base, table protector, counter barrier, color palette and more art crafts. Acrylic plates have higher strength, more heat resistance, UV resistance, cold resistance and corrosion resistance.


Enoin has been an expert in this field over 10 years.
We always put customer's experience into first place.
Our Products have one-year warranty guarantee since the date of purchase.
If there's any quality question, we promise to a refund or a replacement.
Compare with PET sheet or PVC sheet, acrylic sheet has its own irreplaceable advantages. Acrylic panels are harder and tougher than PET panels & PVC panels. At the same time, Acrylic plates are much more transparent, higher strength, more heat resistance, UV resistance, cold resistance and corrosion resistance.
Please kindly note these following tips before your DIY.
1. Before use, please take off the protective cases on each corner and peel off the protective films thorugh holding the Enoin logo label.
2. The acrylic sheets are laser cutting, the panel or the protective films might produce some plastic smell. But due to our rigorous manufacturing, this smell has been decreased as much as possible.
3. To avoid scratch, please keep acrylic sheets away from the children or the old.
Specification:
Material: Polymethyl Methacrylate (PMMA)
Thermal Softening Temperature > 221℉/105℃
Heat Deflection Temperature > 80℃/176℉
Density: 1.2g/cm3 (Glass: 2.5g/cm3)
Transmittance: 92% - 95% (Glass: Impact Strength ≥ 16kg/cm3
Tensile Strength ≥ 61kg/cm3
Resistance: Heat, cold, UV, corrosion.
Processing Method: engraving, painting, laser/hand saw/electric saw/acrylic cutter cutting, drilling, turning tool etc.


Butch
Reviewed in the United States on February 17, 2025
Came in on time. No scratches. Very easy to cut on my Bandsaw. Gives a nice effect on my project.
Bouson
Reviewed in the United States on January 5, 2025
Good clear and unscratched Orange Translucent Acrylic/Plexiglass Sheet.
Annie
Reviewed in the United States on January 31, 2025
There are lots of acrylic out there... and brands sometimes cut differently... I have had nothing but a great experience with this brand and I just LOVE this pink coloring!!
Brent J.
Reviewed in Canada on August 19, 2024
This is a really nice acrylic sheet.
Brian M Holtan
Reviewed in Canada on July 4, 2024
I bought this based on reviews and suggestions of other laser engraver users that it would be fine for a shield to block my D1 10w's blue light. Nowhere in their description does it guarantee it is laser safe - likely for legal reasons; but, I can say it works just fine as other reviewers have suggested.
m
Reviewed in the United States on March 15, 2024
As the title says, this acrylic will be used as a window on a laser enclosure. So here's what I found out.1. The color and apparent OD value was VERY close to the orange acrylic used on the laser module. I could say that it's just slightly possible that it is like a half of a whisker lighter - but it is too close to be certain.2. I saw where others have used this material for the same reason I purchased it. They seemed to be happy to use it this way.... and now that I've tested it, I think I can understand why... good stuff.3. The price for two pieces was not much more than the price for one piece from most of the other vendors... and in some cases it was a LOT cheaper. So it will be good to have a backup piece, in case I need it.4. The thickness and stiffness of the material is pretty good, so it will not be sagging in the middle. That was my only concern before purchasing, and my concern was unfounded. It is plenty stiff enough for my use.5. Pieces were packed in somewhat of a bubble bag, and then placed in an Amazon box - in other words, it was greatly protected. In fact, it came with plastic corner pieces to further protect the corners from the possibility of chipping or cracking.6. Bottom line: would I purchase again, if I had it to do over again? Yes, yes, and triple yes. Definitely happy with material and pricing.Pro Tip: If you need holes in the sheet to mount it, rather than drill it, you might consider using a soldering iron to melt a hole through it. That prevents the material from cracking and making for a solid surface around the hole. The melted ring around the hole can be cut off with an exacto knife, to clean it up. You can also heat up a nail with a torch and push a hole through it, if you don't have a solder iron.I hope this info will help you to make the best decision on whether to purchase or not. Thank you for reading my review!
Daniel Quiroz
Reviewed in the United States on December 9, 2024
I'm not sure if this will actually block the dangerous blue laser light but I still used it as a window for the laser enclosure I built. I figure it's got to be better than a clear window. This acrylic sheet worked out nicely for my enclosure. FYI if you need to make holes in the acrylic, I would highly suggest melting the holes instead of drilling as drilling can crack the acrylic.
Sean Stevens
Reviewed in the United States on November 27, 2024
I was just looking for a panel to give a little shield to my eyes when I have the laser next to me. For the price, tis works really well.
G&T
Reviewed in the United States on November 25, 2024
I was looking for a sheet of acrylic that was a maroon color, but nobody seems to sell a maroon color, they only sell a dark red color. Some dark reds are not dark at all, but this sheet fit the bill all the way around. I did not particularly want a translucent color but the color is fabulous for what I was using it for. And it cut very easy on the laser. It comes in a bigger size than most of the smaller sheets so that is a plus also! I have ordered this more than one time now as the color is great as a maroon. I definitely recommend this product.
Customer
Reviewed in Canada on September 1, 2023
Bit pricier than expected and ships from US. But it does the job as needed
Cecilia T.
Reviewed in Mexico on October 24, 2023
En lugar de acrílico transparente naranja llegó una placa de amarillo sólido :(
Javier Alejandro López García
Reviewed in Mexico on September 25, 2022
Muy bueno
Greg
Reviewed in the United States on December 7, 2022
I installed these into a bathroom cabinet. I felt it was a safer material to use than glass with kids around. The plexiglass was high quality and a good thickness for this application. In my mind I was imaging a little more opaqueness for this application, but the material was actually clear. It was just tinted purple. Maybe not ideal for hiding toiletries.
Recommended Products

$11.98

$ 5 .99 $5.99

4.3
Select Option