Your cart is empty.
Your cart is empty. Features:
Suit for most aftermarket 1/10 servos that use a 25-tooth spline.
For Vehicle Type: for Buggy, Car, Truck, Truggy.
Specifications:
Material:Aluminum
Color:Black/Red/Titanium
Hole to hole size:16mm/18mm
Hole Size:M2.5
Weight:10g
Package List:
1PC x 25T Servo Arm
Customer
Reviewed in Canada on July 27, 2023
The part itself appears to be very good quality, but unfortunately it is to small for the project I got it for
Dmitri H.
Reviewed in Canada on March 22, 2023
Tried on a 2wd stampede, a pretty light 1/10 RC, doesn't even turn the wheels unless driving, would not recommend.
Eric Benton
Reviewed in the United States on November 25, 2023
It’s a good design and good quality. My daughter crashed her stampede into a tree the day this came and broke the stock one so luckily I had this on hand. Perfect for adding strength and steering
Isal Bundy
Reviewed in the United States on November 18, 2023
No spring also takes a special spring didn’t fit had to return for the price I bought one with spring
SR
Reviewed in Canada on April 25, 2023
Description says this is compatible with the Arrma Big Rock ,but it does NOT allow steering linkages to sit at the proper angle so it is NOT compatible. Nice unit, just does not fit the Big Rock as the description says it does.
Kyle R
Reviewed in the United States on April 10, 2023
Works perfectly with my traxxas slash 2wd factory servo!
karl
Reviewed in the United States on August 17, 2022
Looks great, way stronger appearance than a plastic one. Spring is too weak for a tmaxx. Probably better on a small rock crawler or stampede? Overall great deal for the money.
brent guevarA
Reviewed in the United States on April 3, 2022
Wrong size for my voltage. My fault for not checking the size
David
Reviewed in the United States on April 3, 2022
This is a good quality part but it's too small to use on 1/10 scale. The holes are too close together so you have to grind the ends of the tie rod connectors or you can't connect both of them on the same side (top or bottom). It's also shorter then my stock one so it has less throw (makes the steering less sensitive) but it wasn't an issue for me. Also, the distance between the holes will change the toe-in if your replacing one with different dimensions so this is not a directly compaitble replacement for the Arrma Granite Voltage stock plastic piece as it will toe the wheels out by 2MM which is huge. I was able to make it work by also replacing the tie rods with some adjustable 96mm ones. (The tie rods will need to be 97mm to work on the Voltage with this part.) Eventually the holes on the stock pop on tie rods will wear out anyways and start popping off everytime you hit a big bump so at some point you'll end up replacing the tie rods either way but I would've preffered not to have had to grind the ends down to make them fit making them easier to break. There are some other choices on Amazon that would've been a better fit for me but I was able to make it work and as I said, it is a high quality part.
Doug P
Reviewed in the United States on April 2, 2022
The original servo saver for the Voltage broke after just a handful of runs, so ordered a new one. The original is on back order for months, so kept searching for another replacement. This one from DJX looks amazing and is well made; it should last quite a while. Yes, it does fit the ARRMA Voltage, but you will need to shave down the control arms a little, since the spacing of the connections on the DJX are closer than the original. Only took a few minutes with a dremel too, but a sander could also be used.
Bruce Erickson
Reviewed in the United States on December 2, 2021
I ordered 1 of these to see what they were all about. They sounded to good to be true BUT right after the first one came I ordered a bunch more. Great little Servo Saver that actually works and looks good.
Recommended Products
