Your cart is empty.
Your cart is empty.
- Power on delay, plus timing.
- With large transparent time setting knob for setting time easily, 8 pin solder terminal for installation.
- Time Delay Relay used in industrial automation system and mechanical equipment to delay component.
- Relay is a kind of automatil electric switch, when supply with an input value, like electric, magnetic, light or thermal signal,
it wall transfer the controlled circuit automatically and make an abrupt change, when the input value decreased to certain degtee,
it will resume to former state and make the controlled circuit back to the former stare.
- Features LED indicator show power and output status.
Customer
Reviewed in the United States on March 4, 2024
Dual mounting direct to a panel or on a din rail. Would buy again
Del
Reviewed in the United States on March 24, 2024
It's inaccurate throughout the range and unstable/unreliable min - 2 minutes (which triggers less than 1/2 min when the dial says 2) - you can easily tell these are not industrial control grade quality; however, they do function as garage grade project timers. And this the second attempt at getting a timer, has a significant build-quality improvement Vs round 1. Yes, sloppy and inaccurate, then at a fraction of the acquisition burden, I can't complain and would buy again.
hector
Reviewed in Mexico on November 26, 2024
Bueno
Abraham Bolaños
Reviewed in Mexico on April 23, 2024
Precio módico calidad aceptable, tecnología funcional
Mike
Reviewed in the United States on October 31, 2022
IM using this as a power failure alarm. I needed a delay so my hub could fully load back up before the contacts closed. Works great so far
Dan Young
Reviewed in the United States on June 3, 2021
I have purchased this item on 4 occasions and they always worked great. My last order was for 5 timers and 3 of them were defective, would not time and stuck in the energized mode. VERY DISAPPOINTING to learn that I cannot return them.
Michael J Hood
Reviewed in the United States on December 15, 2019
From the description alone I wasn't sure, but if my testing was right, the contacts change state (from the "shelf" states shown on the relay) AFTER the time has elapsed AFTER power is applied to the coil, STAY in that state while power remains at the coil, and fall back to "shelf" IMMEDIATELY when power is removed from coil.It's perfectly fine is this is the function you need - to delay something coming on (rather than to have something stay on for a while after something else goes off)
mario rebodos
Reviewed in Canada on April 7, 2019
use this item in my project at home
Daniel Chu
Reviewed in Canada on September 16, 2018
I'll tell you what my application is. I have a modem and a router. Everytime there is a power outage in my house, I have to manually cycle power to my router to get my WiFi up. What this does is to delay my power up on my router so I no longer have to do it manually. When I am travelling and I have a power outage, I was not able to connect to my house remotely but now I can.
Bryan S
Reviewed in the United States on August 31, 2018
They are really nice when they work, I use them to control SSR's so they don't have a big load on them. I bought two and one didn't work, sounded broken inside. I imagine they way they pack and ship them is probably rough on the insides.
Randy Stanard
Reviewed in the United States on March 25, 2018
I would give this little device 10 Stars if it were allowed. This device does EXACTLY what I need it to do.My application is to delay an external hard drive in docking station connected to a router to record videos and images from security cameras.I have a sensor to monitor loss of internet connection. When this happens, modem and router are restarted.The problem is that if you turn on the hard drive before the router is fully initiated, then the hard drive is not recognized by the router. Video/picture are no longer saved to hard drive because hard drive is not recognized by the router if hard drive powered up too soon.By giving the hard drive about a 5 minute delay before powering up, it solves this problem perfectly. Router restarts and fully initiates, then 5 minutes later hard drive comes onlline and connects perfectly to the router making is accessible via the local network.This device is inexpensive, yet works like a charm to solve a maddening problem.I wired it into the system by purchasing a 2 ft extension cord from Amazon, cutting the black and white wires, but allowing the common to continue from end to end.The black wire from the power source (110v plugin) was connected to terminals 12 & 14, tied together. The white from the 110v plug was connected to terminals 9 & 13, tied together.On the other side (where the device is connected, (in my case hard drive) the black wire connects to terminal # 8 and white wire to terminal # 5.If you want to protect from anyone touching exposed 110 volt terminals you can cover it with black silicon, again purchased from Amazon. That is what I did to make for a safer installation so you do not experience a shock should you accidently touch the open terminals.Great Device. Could not be happier with my purchase.
Acheteur
Reviewed in Canada on December 3, 2018
Tou fonctionné très bien
T. Pariseau
Reviewed in the United States on November 7, 2018
I bought this relay to modify a power strip to delay power to our wireless router and network switch at power on. The router requires that the cable modem be fully powered up and initialized first else it will not connect. This poses a problem if power is lost because the router would not initialize properly. This relay senses when power is restored and turns the router and switch on 2 minutes later, allowing the cable modem to fully boot up. Works flawlessly. Great product.
Recommended Products
