Your cart is empty.
Your cart is empty. This PoE injector only for 10/100Mbps Device (Not fit for Gigabit Device); iCreatin PoE Injector can save you money by using an existing Ethernet line to deliver data and power.
This PoE Injector can easily connect any IEEE 802.3af-compliant device to a non-PoE LAN switch port.
This PoE Injector can be used to connect a wireless access point, IP phone, network camera, or any IEEE 802.3af powered device to a LAN switch.
Reduce Wiring Costs With the iCreatin PoE Injector you can dramatically reduce wiring costs by powering devices through your existing Ethernet line rather than running new AC power lines.
To use this PoE injector, all you need to do is connect the iCreatin PoE Injector to the LAN switch port, and then use your existing Ethernet Cable to deliver DC power and data to your device.
Protect Your Equipment Now that you are running DC power to your networked equipment through the Cat5 cabling, you need to be sure that your devices are protected from power problems.
The iCreatin PoE Injector is designed with short circuit protection Over Current and Over Voltage Protection, keeping your devices safe.
Specifications
2 RJ45 Ethernet ports
Max 30W Power output,
Power feed: V+ 4,5; V- 7,8;
Deliver power up to about 328feet(100 meters)
Support 100-240V voltage input
What in Box?
1 x Desktop PoE injector
1 x US power cord
M C
Reviewed in Canada on March 6, 2024
This is a basic and fully functional POE injector. You plug one end of it into the wall and there are 2 ports, one is where you plug in your networking cable (input), and the other side is the combined POE output that merges the networking input with power. It has a detached power cord which is handy so it isn't a big brick that blocks the whole power outlet. The only downside is that this cannot be easily mounted to the wall or anything.
michael callwood
Reviewed in the United States on February 18, 2024
Used this product to supply power to a Cisco VOIP phone.
Bridgit
Reviewed in the United States on April 27, 2024
Used for a 200meter POE run. Worked great.
Karen A. Brady
Reviewed in the United States on April 26, 2024
I use this to power a POE Wireless Attachment Point. It installs easily and does the job.
Doc K
Reviewed in the United States on September 2, 2023
This works just fine for my Ubiquiti 6 lite, but be warned it's not gigabit. Clearly says so in the title, so shame on me for not paying attention. But other than that, serves it's purpose.
Jos
Reviewed in Canada on July 16, 2023
Bonne qualité
Isound solutions
Reviewed in Canada on November 10, 2023
Very good quality and also good for ubiquity access points
Customer
Reviewed in the United States on January 21, 2023
Needed POE injector to power a network extender. Good product. Great brand. Did the job.
FRANCOIS DRIEN
Reviewed in Canada on June 5, 2021
Conforme aux attente
Customer
Reviewed in the United States on April 6, 2021
Arrived quickly, shipped in appropriate container which prevented any damage. I plugged it in and my camera SV3C came right up. I could not ask for more for such an inexpensive device. This saves me from having to pull power for receptacle at the point where i will mount this camera. I feel dumb for not ordering this thing sooner - will buy a couple more for other cameras.
Alex
Reviewed in Canada on September 23, 2020
It is not 48v as advertised. It is in fact 24v.
Fred Murphy
Reviewed in the United States on January 18, 2020
Good product but only 3 stars because the title is untrue. Why lie? Just say it powers 802.3af devices.the device delivers easily 15 watts, and actually goes to 22 watts without issues. It is Mode B ( pins 4&5 plus, 7&8 minus) which will power almost all 802.3af devices ( maybe 98% accept mode B) but only if all 4 pairs are connected in the cable.The device is NOT 802.3af compliant. This is a passive device - so if you plug in a laptop or printer by mistake, into the PoE port - there will be damage. An 802.3af compliant device has protection built in - it will not apply power unless the device plugged into the PoE port is 802.3af and able to receive power without damage.The earth ground on the AC cord does not connect to the shielded RJ45 connectors - so don't bother using shielded cables.So use with caution - and enjoy a good product at a good price. Most 802.3af devices do not need even 5 watts - so there should be no problem with this. Note: 802.3at devices will not power properly because even if this device can deliver 25 watts ( more than specified) it does not have the chip inside to inform the 802.3at device of the available power.
L W
Reviewed in the United States on January 1, 2016
This is a great POE injector. I bought it to power my POE PTZ security camera. My camera can use up to 18W peak, and this is one of the few POE injectors that can output enough power for my camera. I went with a POE injector instead of a POE switch because a lot of the POE switches don't have enough juice to power all the security cameras that are connected to it. Be sure to check your POE power draw specification and the POE injector (or POE switch) power output.The hardware came very well packaged. The only complaint I have with this product is the LED is quite bright. It doesn't matter to me because it is installed under a desk so no one sees it. If it is too bright for your use, tape over it or flip it over so the LED faces down. It also comes with a nice 3-prong thick power cable.Overall, great product. I will be buying a couple more of this when I order my next set of POE cameras.
Recommended Products
$49.99
$ 26 .99 $26.99